Search: philips
Results: 14206
Make Model Symptom Problem Solution By
PHILIPS 42PFL3604
Doesn't start No standby voltage, LED off, no signal Check the primary coil (in my case it was broken), replace the 4.7μF x 450 v capacitor, it was swollen. After replacement it started working again! Augusto Azeredo
PHILIPS 32PFL5607D/78
It doesn't turn on, it just stays on standby, the LED lights up white and goes to red Normal power supply voltages, grounded stand by pin, black light comes on and generates all voltages I did a reset, holding volume + and the arrow key (input) while plugging it into the socket, it worked normally after that. ser-mga
PHILIPS FWM416/78
Shows disc reset fall when inserting the usb pen driver Lack of reset on the CD due to lack of power Causes capacitor 168 to short on the 8v line. After changing the capacitor, the 8v came back and the device rang normally
PHILIPS 40PFL9605D
?
The TV turns on, the image appears and then it turns off, only the sound remains. Guys, the cause is q702 and q703, these two transistors are responsible for the switching of the transformer that feeds the 185 volts to the LED bars, I replaced the two fets and everything was resolved. Replace the two fets q702 and q703 that were leaking and everything is resolved, let's stop being selfish and help others. <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small>
SOM PHILIPS FWM210
Display does not show characters After evaluating the board, I noticed that tsound was no 10 volts (I put a 560 omhs resistor on the r524 that tsound was no board and the sound started working again eletronica max es
PHILIPS 14PT414A
Does not turn on, power supply less than 20v C2540 100µ 25v Changing the c2540 close to the power supply trimpot Marcelo Piranga
PHILIPS FX30X/78
FX30
Doesn't start N channel mosfet (q13) does not switch the +5va to the panel. Replace the component. barcelos32
PHILIPS 32PFL3008
Dead C709 smd na pci main I took it out Adrian Chapadão do Céu Goiás
PHILIPS 40PFG6110
TV 715G6677-P02-001-002H
Did not turn on inoperative Power outage Smd diode d9311 short swap Júnior eletrônica
PHILIPS 32PFL5604
In my case the defect was in c120, on the screen board. dismantle the screen to gain access. replace c 120, short. Check "t-com" board voltage at c60,61= 0v, it must be 26v. see c110,115=0v, it has to be 16v. In my case the defect was in c120, on the screen board. dismantle the screen to gain access. replace c 120, short. arock
PHILIPS 32PFL3404
Turns on and after a while it turns off or the relay keeps hitting Troque na placa principal.. c474, c532, c534 C474, c532, c534 José Oscar da Silva
PHILIPS 32PFL3404
TV turns on and off or the relay keeps hitting.. C474 defect on main board Replace c474 na 4.7 aluminum main plate.. José Oscar da Silva
PHILIPS 39PFL4707G
Nothing turns on, not even the STB LED Voltage of 5v with approximately 2.5v Replace the power supply capacitors on the 5v line
PHILIPS NTRX700
Very low sound R 304 100r burned and diode d303 shorted Just replace and run to the crowd Wenceslau
PHILIPS 32PFL3008D/78
The LEDs turned on and off. I changed the memory and it was upside down. I solved it with code. 062598 + little house + 002 I will deliver to the customer PIG QUILES
PHILIPS 32PFL4606
Does not turn on intermittent Cold welding trafo power supply Gilmar L.
PHILIPS 40PFG4109
With sound without image With sound without image and LED on, check c06,c08,07 on the screen board next to the diode Cabeça
PHILIPS 42PFL3604
Does not generate 3.3v Burned fountain Replace without measuring, u801 ci fs510 / d813 her108 / d809 sr160 / os photo u802 and u804 / r825 put 4r7 up to trafo /c806 4.7 x 450v JORGETVPARANA
PHILIPS 43PFG5000/78
No image, just lights up the LEDs C216 na regua do display Replace c216 or check for another fault. ELETRONICA AUDIO E VIDEO BIRIGUI-SP
PHILIPS 20PT3336
Turns on, the image appears and then turns off. 47 by 250v electrolytic capacitor (c2564) Replace. Ferraz