☰

Philips Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philips
Results: 14210
Make Model Symptom Problem Solution By
PHILIPS 2A
140v voltage is 120v. stand-by and ext1 leds are on. Diode 6663 (1n5062; 4822 130 41275) short-circuited, ic7830 (mab8441p/t001; 4822 209 11037) defective. remarks : only for sets with citac module.
PHILIPS 29PW6332/05
No text, no dolby or zoom features not working Reset options using service tool press "align" a menu appears reset relevent options from "n" to "y"
PHILIPS 29PT9416 MG7.1
Service mode entering Use the standard remote control and key in a special sequence '0,6,2,5,9,6' followed by pressing the 'menu' button. if the main menu also appears with the service menu just press 'menu' again to clear it.. the other way is to short the two service pins on the signal panel (pins 2 and 3 of connector 0356). the advantage of this last method is that all the software protections are turned off.
PHILIPS 29PT9113C
White box bottom left of screen Auto subtitle selected switch off from handset
PHILIPS 29PT8444
Correction to position 21 of styling 220 Correction to position 21 of styling 220 of product survey 1999-3 (3122 785 10300 the code numbers mentioned for the aluminium columns at position 21 of styling 220 are not correct. the correct code numbers must be: 21 4822 466 12216 aluminium colum
PHILIPS 29PT8434
Correction to position 21 of styling 220 Correction to position 21 of styling 220 of product survey 1999-3 (3122 785 10300 the code numbers mentioned for the aluminium columns at position 21 of styling 220 are not correct. the correct code numbers must be: 21 4822 466 12216 aluminium colum
PHILIPS 29PT8424
Correction to position 21 of styling 220 Correction to position 21 of styling 220 of product survey 1999-3 (3122 785 10300 the code numbers mentioned for the aluminium columns at position 21 of styling 220 are not correct. the correct code numbers must be: 21 4822 466 12216 aluminium colum
PHILIPS 29PT8419
Corrections on service manual em1a aa Page 4 chapter 2: it was forgotten to mention here in this chapter that the architecture is 'hot'for a big part. e,g. deflection is 'hot', but also the middle big heatsink. so be warned. page 16 chapter 5: sam-menu on right hand top side, sho
PHILIPS 29PT8319
Corrections on service manual em1a aa Page 4 chapter 2: it was forgotten to mention here in this chapter that the architecture is 'hot'for a big part. e,g. deflection is 'hot', but also the middle big heatsink. so be warned. page 16 chapter 5: sam-menu on right hand top side, sho
PHILIPS 29PT828C
Trips from green led to red to green to red Replace ic7450, and ic7550 on audio pcb
PHILIPS 29PT828C
Stuck in standby Resolder scan coil plugs
PHILIPS 29PT6231
Interference from adjacent channel Check, and replace/change posn: 1145 (saw filter) on chassis to 2422 549 44223 ofwk7260m for /79r, add posn: 1168, 4822 242 81572 6mhz ceramic filter remarks : solution implemented in production
PHILIPS 29PT6021
Sdm does not work by shorting service pins. Measure pin 19 of simm connector 0226 on lsp, if it is 2v (normal is 1v) then add a resistor of 1k8 between pin 19 of the simm connector and ground. make sure counting left from pin 1, do not use the pin no. printed on service print! see attached ph
PHILIPS 29PT5324
Picture distortion (moire) visible. Picture distortion (moire) visible in the top of the screen. using one of the ext-inputs, a picture distortion will become visible in the top of the screen as a horizontal bar (moire-effect). this distortion is more visible when brightness value is betwe
PHILIPS 29GX1995 ANUBISS/BB
Dead Replaced - diode 6528 (bzx55) and 6519 (bzx55), resistor 3503 (1.5r 7w), ic 7510 (uc3842bn) and fet 7513 (h12n60f1).
PHILIPS 29DS100
Unable to switch channel from pr1 to pr2. Check and replace if necessary position 7002 on the ssp into mg21a11.6_01901 (3104 317 41901) iris code : 1272
PHILIPS 28PW6515/05
R/c inop Dry joints on ic7064 solder with care dual layered pcb.
PHILIPS 28PW6515/05
No raster eht ok. int trips if screen volts turned up D6832 o/c on crt in4148
PHILIPS 28PW6332/05
Volume bars not visable when using handset Press "menu" on tv untill volume bar displayed then press "i" for 3 sec
PHILIPS 28PW6332/05
No txt, scart skts not wotrking, increased height, no zoom, no widescreen etc Faulty eeprom, change then go into service default by shorting two t.p out on small signal board, then pressing menu and - on tv all settings will be self evident.