☰

Philips Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philips
Results: 14245
Make Model Symptom Problem Solution By
PHILIPS 29PT8434
Correction to position 21 of styling 220 Correction to position 21 of styling 220 of product survey 1999-3 (3122 785 10300 the code numbers mentioned for the aluminium columns at position 21 of styling 220 are not correct. the correct code numbers must be: 21 4822 466 12216 aluminium colum
PHILIPS 29PT8424
Correction to position 21 of styling 220 Correction to position 21 of styling 220 of product survey 1999-3 (3122 785 10300 the code numbers mentioned for the aluminium columns at position 21 of styling 220 are not correct. the correct code numbers must be: 21 4822 466 12216 aluminium colum
PHILIPS 29PT8419
Corrections on service manual em1a aa Page 4 chapter 2: it was forgotten to mention here in this chapter that the architecture is 'hot'for a big part. e,g. deflection is 'hot', but also the middle big heatsink. so be warned. page 16 chapter 5: sam-menu on right hand top side, sho
PHILIPS 29PT8319
Corrections on service manual em1a aa Page 4 chapter 2: it was forgotten to mention here in this chapter that the architecture is 'hot'for a big part. e,g. deflection is 'hot', but also the middle big heatsink. so be warned. page 16 chapter 5: sam-menu on right hand top side, sho
PHILIPS 29PT828C
Trips from green led to red to green to red Replace ic7450, and ic7550 on audio pcb
PHILIPS 29PT828C
Stuck in standby Resolder scan coil plugs
PHILIPS 29PT6231
Interference from adjacent channel Check, and replace/change posn: 1145 (saw filter) on chassis to 2422 549 44223 ofwk7260m for /79r, add posn: 1168, 4822 242 81572 6mhz ceramic filter remarks : solution implemented in production
PHILIPS 29PT6021
Sdm does not work by shorting service pins. Measure pin 19 of simm connector 0226 on lsp, if it is 2v (normal is 1v) then add a resistor of 1k8 between pin 19 of the simm connector and ground. make sure counting left from pin 1, do not use the pin no. printed on service print! see attached ph
PHILIPS 29PT5324
Picture distortion (moire) visible. Picture distortion (moire) visible in the top of the screen. using one of the ext-inputs, a picture distortion will become visible in the top of the screen as a horizontal bar (moire-effect). this distortion is more visible when brightness value is betwe
PHILIPS 29GX1995 ANUBISS/BB
Dead Replaced - diode 6528 (bzx55) and 6519 (bzx55), resistor 3503 (1.5r 7w), ic 7510 (uc3842bn) and fet 7513 (h12n60f1).
PHILIPS 29DS100
Unable to switch channel from pr1 to pr2. Check and replace if necessary position 7002 on the ssp into mg21a11.6_01901 (3104 317 41901) iris code : 1272
PHILIPS 28PW6515/05
R/c inop Dry joints on ic7064 solder with care dual layered pcb.
PHILIPS 28PW6515/05
No raster eht ok. int trips if screen volts turned up D6832 o/c on crt in4148
PHILIPS 28PW6332/05
Volume bars not visable when using handset Press "menu" on tv untill volume bar displayed then press "i" for 3 sec
PHILIPS 28PW6332/05
No txt, scart skts not wotrking, increased height, no zoom, no widescreen etc Faulty eeprom, change then go into service default by shorting two t.p out on small signal board, then pressing menu and - on tv all settings will be self evident.
PHILIPS 28PW6324/05R SA8.0E
Dim raster with sound rgb o/p chip on crt base overheating Tapping crt neck brought back pic - crt faulty
PHILIPS 28PW6324
Tripping with st/by led pulsing Fb tuning cap 1n5 2kv burnt
PHILIPS 28PW6305 A10
No red Ic7301 u/s tda88858q.
PHILIPS 28PW5324/05R
Poor pic with green tint & fb lines Dry joints loptx
PHILIPS 28PT7306
Wrong codenumbers are mentioned in styling 261. ps 2000-2/3 In product survey's 2000-2 and 2000-3, some wrong codenumbers are mentioned in styling 261. see list below for the correct codenumbers: 6a* 3104 328 01612 cabinet 6c* 3104 328 06051 cabinet 6d* 3104 328 07142 cabinet 11a* 3104