Philips Repair Tips

Search: philips
Results: 14244

Make	Model	Symptom	Problem
PHILIPS	14PV263/02	Option code: 23532	From week 02/97 onwards the option code is printed on the typesticker. always use this code ! for early sets without this information on the typesticker, the option code is: 23532
PHILIPS	14PV263/02	New vps ic sda5642-6 (pos. 7840)	Since production week 9741 a new vps ic pos. 7840 (sda5642-6) is introduced in production. this ic is not compatible with the previous one. when ordering, look at the printing on the ic ! old: sda 5642-5 - codenumber 4822 209 32728 new: sda 5642-6 - co
PHILIPS	14PV263/01	Option code: 24492	From week 02/97 onwards the option code is printed on the typesticker. always use this code ! for early sets without this information on the typesticker, the option code is: 24492
PHILIPS	14PV263/01	Codenumber information - new software	A new software version (ptcp2-7) is available for the control up (ic 7801). service codenumber is 4822 209 15271. this new version is only used in the following sets: 14pv263/01, 14pv162/01, 14pv162/05, 14pv162/07, 14pv163/05, 14pv163/05h, 14pv263/01,
PHILIPS	14PV263	Strange colours after recording.	Check chroma ic7051 (4822 209 90538).
PHILIPS	14PV263	Start up problems after replacing ts7352	When ts7352 is replaced, it can happen that the set doesn't start up properly. there are 2 possible solutions for this problem: - use sgs type mtp3055e (4822 130 63726). - in case of a motorola type mtp3055v (4822 130 60838), add a 22 uh coil soldered
PHILIPS	14PV263	Start up problems	When the set is switched on by the mains-switch while a cassette is in the set, the front led starts blinking, but the set doesn't start. solution: check the primary voltage (ubat) and adjust this for 14" sets to exactly 101.5 volt. (see chapter 3.1.1
PHILIPS	14PV263	Spare part information	If the lever inside the mains-switch is broken, the switch doesn't remain in the "on" position. solution: replace the switch by a new one. improved switches of a newer production range are on stock. (4822 276 13542)
PHILIPS	14PV263	Spare part information	A repair kit , containing pulley shaft + worm shaft (pos. 47+48) is delivered with codenumber 4822 310 10657. this kit can be used for all turbo- and eco mechanisms !
PHILIPS	14PV263	Set produces audible noise in stand-by	Add a small lebl (leading edge blanking) pcb, to avoid auto oscillation of transformer 5330 (or 5331). a modification letter is included with the lebl pcb. this pcb is available with service nr. 4822 214 12173.
PHILIPS	14PV263	Set produces audible noise in stand-by	Add a small lebl (leading edge blanking) pcb, to avoid auto oscillation of transformer 5330 (or 5331). a modification letter is included with the lable pcb. this pcb is available with service nr. 4822 214 12173. since production week 9723 this circuit is
PHILIPS	14PV263	Memory erase procedure	The contents of the memory can only be cleared via the service mode. this option is not available for end users. (risc of destroying option codes). service mode: press "stop" on remote control and "play" on the set for 5 seconds. select the second page
PHILIPS	14PV263	Key set	The key set assy has been codified for all b-range tvcr's. this will allow to change the keys without having to change the complete frame. servicenr. 4822 410 11075. key set for: 14pv263/01/02/08/13 - 14pv264/39 - 14pv163/05 - 14pv172/01/05/08/13/39 - 14
PHILIPS	14PV263	How to activate/de-activate "hotel mode"	Activation: - set volume to desired level. - select programm 38. - press the stop button of the remote control and the stop button of the vcr for about 5 seconds, until the message h+ appears. de-activation: - set volume to desired level. - select p
PHILIPS	14PV263	Correction service manual 14pv263/01	The indication of the small-signal pcb (page 1-3) is wrong. the right indication is psspp3/gpvxf. this pcb is only applied in 14pv263/01.
PHILIPS	14PV263	Codenumber information	Please add following codenumbers to the service manual: lift-flap 14pv263/01 : 4822 443 10404 lift-flap 14pv263/02 : 4822 443 10404 spring for lift-flap : 4822 492 70896
PHILIPS	14PV263	Codenumber information	The codenumber for the spacer between on/off switch and the knob (pos 3) is 4822 402 10702.
PHILIPS	14PV263	Codenumber correction	The codenumber for the scanner-motor (pos. 34) in the service manual is wrong. the correct codenumber is 4822 361 215 48.
PHILIPS	14PV263	Codenumber correction	The codenumber of pos. 1701 (tuner) for 14 inch sets with iec input is 4822 210 10691 (uv916s).
PHILIPS	14PV263	Calling installation menu	The installation menu is activated by the following procedure: - switch on the set by means of the stop key. - press simutaneously the cursor left and the cursor right key on the remote control.