Philips Repair Tips
Search: philips
Results: 14244
Results: 14244
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
14PV210
|
No pic; r3199 burnt | R3199 (9k2) and d6183 (smd) used 1n4148 in lieu | ||
| PHILIPS |
14PV210
|
Fault codes | Record led flashing >>>error in eeprom1[ic7818]; timer led flashing>>> error in eeprom2[ic7801]; stdby led flashing>>> error in textmicro[ic7804] | ||
| PHILIPS |
14PV202/07
|
Int blows fuse at sw on | Replace degauss coil, degauss posistor and 1.25 amp fuse | ||
| PHILIPS |
14PV200/07
|
Dead apart from popping sound at sw on | D6391 byw98 200 rated at 3a s/c - used by399 in lieu | ||
| PHILIPS |
14PV200/07
|
"n act" shows at sw on | Switch the combi off with the mains switch. depress and hold both the wind & rew buttons on the combi while switching back on (keeping the buttons pressed for around 5 seconds) release the buttons and this should clear the memory and allow the combi to be setup as normal | ||
| PHILIPS |
14PV184
|
Reverts to st/by at sw on aft loptx replacement (led goes from brief green to red) | Eventually comes on with dull grey raster. prot line on micro ic7801 pin 53 vcr pcb only 1v (5v) - check at d6568 lh plug 1923 - prot tr 7550 bc547 leaky (front left edge of tv pcb) | ||
| PHILIPS |
14PV184
|
Menus not displayed | L1802 on bottom panel across pins 42 & 43 of micro ic7801 | ||
| PHILIPS |
14PV183ETC
|
Service mode adjustments | Press "stop" on handset & "play" on keyboard together for 5 seconds | ||
| PHILIPS |
14PV183ETC
|
No chan +/- on r/c after eeprom replacement | Enter service mode & set correct option number - to be found on back plate of set | ||
| PHILIPS |
14PV183ETC
|
Hotel mode activate/deactivate | Press "stop" on handset & "stop" on keyboard together for 5 seconds while on channel 38 | ||
| PHILIPS |
14PV183
|
To enter service mode | Press "stop" on r/c & "play" on keyboard for 5 seconds | ||
| PHILIPS |
14PV183
|
To activate/deactivate "hotel mode" | Press "stop" on r/c & "stop" on keyboard for 5 seconds while on ch 38 | ||
| PHILIPS |
14PV182/05
|
Osd missing | L802 7.4mhz osc coil o/c pt no 4822 157 71289 | ||
| PHILIPS |
14PV182 COMBI
|
Dead with tape stuck in machine | Loptx | ||
| PHILIPS |
14PV182
|
Tripping on & off at 1 sec intervals | Mc4403 chip ic7130 in psu | ||
| PHILIPS |
14PV182
|
St/by only with vcr shuffling constantly | Loptx - had hole in it | ||
| PHILIPS |
14PV182
|
No r/c operation | Ir pickup module has no o/p although its supply is correct - replace part no 4822-218-11745 | ||
| PHILIPS |
14PV182
|
No r/c operation | Replace i.r pickup unit on vcr front pcb part 4822-218-11745 (seme) £3.44 | ||
| PHILIPS |
14PV182
|
Dead, tripping | T7583 but12af s/c on main pcb | ||
| PHILIPS |
14PV172
|
Start up problems after replacing ts7352 | When ts7352 is replaced, it can happen that the set doesn't start up properly. there are 2 possible solutions for this problem: - use sgs type mtp3055e (4822 130 63726). - in case of a motorola type mtp3055v (4822 130 60838), add a 22 uh coil soldered |