Philips Repair Tips
Search: philips
Results: 14206
Results: 14206
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
29PT4643
L04U |
Vertical closed from the middle up. | Capacitor c2465 (10x100v) and 1k2 resistor (no marking on the board) connected to the anode of the smd 6458 and cathode of the 6457. very close to the replaced capacitor. As a precaution, resolder possible cold soldering points. | Eletrônica R-Tec | |
| PHILIPS |
FWM582/BK
|
No audio at subwoofer output | 47x63v c423 | Capacitor replaced | Artagnan |
| PHILIPS |
29PT558
|
Vertical at the top with retrace and skipping the retraces on top of this fold | All components were good. I just resoldered the ci terminals and it was ok | ||
| PHILIPS |
40PFL3805
|
Turns on the image and then turns off | Resistor r515, r516, r517, r518 with changed values. | Measure and replace any that are altered. | GL Eletrônica BH |
| PHILIPS |
PHILIPS
|
Turns on the image and then turns off | Resistor r515, r516, r517, r518 with changed values. | Measure and replace any that are altered. | GL Eletrônica BH |
| PHILIPS |
32PFL5403
|
Does not turn on, LED flashes 4x | 2p34 smd cap short | JOAOMVJR | |
| PHILIPS |
NX5
|
Device turns on, volume button doesn't work and its LEDs flash, other buttons don't work | C507 (47uf x 10v) connected to pin 14 of u501 on the control board | Can be replaced without removing the board, desoldering the positive pin and soldering another capacitor | shermanflima |
| PHILIPS |
29PT8457/78
|
Does not oscillate power supply | Primary chopper obs the small one | jR eletronica lagoa do ouro pe | |
| PHILIPS |
FWM998X/78
|
When I plug it in, the display lights up and immediately returns to STDBY. I press the power key, the symptom repeats itself. Turn on the fan, turn it on, and stdby. | Checking the power supplys, negative power supply (-40v) was missing | D 18, in the shorted power supply, one of the sides. I replaced it and everything was resolved. | arock |
| PHILIPS |
42PFL3604/78
|
Does not operate via remote control | On the remote sensor plate smd c1 capacitor with leak | Just removed it and it started working again | PATRICK |
| PHILIPS |
52PFL8605
|
Front LED 2 blinks does not turn on the TV | Capacitor 2u15 ,2s29 | I removed it to remove the short | Roberto Costa |
| PHILIPS |
FWM6500
|
Dead | Diode d15 | Replace for another | Fernando |
| PHILIPS |
NX5
|
CD and USB keys don't work without sound | Leaky keys with a lot of dust and especially the 34-way flet combo, pay special attention to it, I went a long way to get to it | Exchanging them was beautiful | washington |
| PHILIPS |
FWM9000X 78
|
LEDs stopped working | Immediate | Arthur | |
| PHILIPS |
20PT326A/78R
|
Turns on but no image, touching the screen comes a reddish screen with retrace lines | Resolder smd components on the tube board, in my case it was the 3332 resistor | Claudio Luis Negrini | |
| PHILIPS |
32PHG4900
TPM 15.5L LA |
No audio | Enter service mode (062596+ info key) go to the codes option, enter the option codes that are the same as the codes that are located on the back cover of the television and save, turn the TV off and on to exit and the TV worked perfectly | rubertan eletr silva joão monlevade | |
| PHILIPS |
42PFL3507D/78
|
Normal power on, white screen, with sound without image | C193 shorted on t-con board | cylon34 | |
| PHILIPS |
20PT529A
|
Blurred/turning off | R3204 | Replace and run for the hug... ums | |
| PHILIPS |
42PFL3604/78
|
The backlight does not come on or it just blinks. | After saving this power supply board with the defective components, I set it up on the bench and the TV only blinked. | C802 of 0.47/1 60 with replaced color however the biggest villain was the trimpot rw977 of 10k replaced to megas. I'm just exchanging them and joy | Rômulo |
| PHILIPS |
HTS6120/55
|
It doesn't turn on just STB. | Capacitor c929 at the power supply shorted. | Replace and run for the hug. | Marcos |