Philips Repair Tips

Search: philips
Results: 14206

Make	Model	Symptom	Problem	Solution	By
PHILIPS	21PT6456	I'm sound	I'm sorry		INTERTEC ELETRONICA
PHILIPS	FWM35/19	Device works normally, suddenly turns off and stays in demo mode (demo mode)	Panel contact key with low conduction or altered, place the analog multimeter on scale x10, remove the key from the PCI and test it on that scale and see if it conducts a little without pressing it, if it does, replace it with another one, If it is normal, remove all the others from the PCI and do the same test, sometimes some of them will be altered	Check it out, these tricks are a lot of mistakes, as they replace and the device goes crazy, they are these (1405, 1406, 1408, 1424, 1426, 1421, 1420, 1422, 1423, 1419, 1418, 1416, 1417, 1411, 1410, 1415 , 1412, 1413, 1414), front panel sw switches	rubertan
PHILIPS	FWM35/19	Carousel drawer locked	Shorted drawer motor	Replace it for another	rubertan
PHILIPS	FWM35/19	Does not turn on, no standby	1n4148 diode open, brown glue on it caused it to oxidize and open it, when I removed it from the PCI it broke in half	Replace it (d723) it is positioned next to the capacitor (c796) and the resistors (r805, r806)	rubertan
PHILIPS	FWM35/19	Without audio CD does not work and carousel drawer does not open	Altered diodes on the main PCI, these little rascals alter their conduction and the voltage passing through them drops by half or completely resets if you test them on the PCI with the analogue multimeter, some of them will be altered, but for a more guaranteed service it is preferable to change them all, If you touch the soldering iron to one of its terminals, they will start to conduct and the device will work, be careful, don't trust, change them all	These are these little rascals, they are on the main PCI wsound the power audio ci is located, sound they are (d746, d745, d744, d743, d742, d741, d740, d748)	rubertan
PHILIPS	FWM35/19	No audio cd drawer doesn't work	Diodes connected in series changed together with regulator ic702 (ka7812)	Replace these diodes as they alter their conduction, if you test them on the PCI with the analog multimeter some of them will be damaged but	rubertan
PHILIPS	42PFL3507D	Tecon blowing fuse	D08 c209		genri maquine
PHILIPS	32PFL3605	Red LED flashes but nothing turns on	C.i of 8 terminals in position 7800 below the electrolytic 2804 of 100x16	C.i broke and that's why I couldn't identify the code, I took another one from a scrap card.	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	21PT5435	Turns on and off in seconds	Diodo smd 6451 so replace	Diodo smd 6451 so replace	DJ PITUKA
PHILIPS	FWM462	I'm sound	Lack of 1.2v voltage on pin 6 of the sound outputs,	Replace 10k resistor r722, it was open (8817)	MARCOS MELO. CEARA
PHILIPS	NTRX500X/78 MX5 MX7	It turns on, but tsound is no command on the function keys and the Bluetooth keeps flashing and the speaker keeps clicking every three seconds.	Problem with the internal reset of u501 pin 38 - dacvmid- gp/io. behavior changes over time. bad component.	Replace capacitor c521- 47μF, for 1μF	LUCIANO ALQUEJA
PHILIPS	HTS3410D	Does not turn on, STB LED flashes.	Power supply inoperative.	Caps 985, 987 and 989 were inflated, replaced and device working.	Scds
PHILIPS	32PFL3606 L11M1 1L	Does not turn on, does not have a 1.80 volt supply	1.80 volt regulator 7124 broken	Replace	antonio nobrega patos pb
PHILIPS	32PFL4007	It doesn't turn on, the power supply has 4.7v.	Reg. u702 3v3. replace.		Joaomvjr
PHILIPS	32PFL3404	Does not come out of standby	Removing the power supply connector in socket p22 on the main board or on the power supply and replacing it again with the power cable connected, then it works, serves the control and everything else. If you remove the socket from the mains, you return to the same problem and do not respond to any command.	Capacitor c474 de 4,7mf/16v	Helio Eletrônica
PHILIPS	32PFL3404/78	Does not come out of standby either via the controller or the keyboard	Removing the power supply connector in socket p22 on the main board or on the power supply and replacing it again with the power cable connected, then it works, serves the control and everything else. If you remove the socket from the mains, you return to the same problem, nothing else matters.		Helio Eletronica
PHILIPS	29PT4631/78	Wouldn't turn on without +b	Photo coupler 7515 burnt		Reginaldo Alves
PHILIPS	32PFL3506/F7	Standby LED blinks but does not start	After a lot of searching I found the shorted speaker that activated the power supply protection		Marco
PHILIPS	32PFL7762D/12 LC7.5E LA	No image and no sound. with OSD menu, white screen, no tuning.	Main board		Edson SP
PHILIPS	32PFL6615D/78 Q551.1L LA	LED blinks 3 times	Resistor r219 - 130r open on the power supply board - brown, orange and black	I replaced it for a 100r one with higher power, that's what I had at the time and the TV worked.	Sambaquy