Search: philips
Results: 14252
Make Model Symptom Problem Solution By
PHILIPS 53TP60C
Poor clo correction. Check adjustment of width trimpot r469. * 10jan96 anc. check capacitor c453 (3.3nf). * 15Oct97 anc *.
PHILIPS 53TP60C
Colored outlines in the image (rgb). Integrated IC11 (X24C08P). * 11Apr96 BC *. check if fuse f2, if it is open check Possible short on red q107. * 04Jul96 ac *. check for possible cold soldering on power transistors, e.g.: in red see q356. *
PHILIPS 53TP60C
Commands do not work (all). Check integrated ic301 (613029). * 18Sep97 anc *.
PHILIPS 53TP60C
With list(s) in horizontal direction. Verificar capacitor smd c554 (.022) trincado. * 22ago97 anc.
PHILIPS 53TP60C
Burning or smoky smell. Being from the convergence board: resistors r279/ r261/ r262 /r211 and r212, check integrated ic210, there should be +0.6v at pin 3. *10jan97 anc*.
PHILIPS 53TP60C
Varying or intermittent brightness Check possible cold solders on the "digmod" terminals. *27Aug97 anc*.
PHILIPS 53TP60C
Poor brightness (little shine). Check possible lack of +130v cable p404 with pin 7 interrupted. * 25Aug97 anc *. check resistor r817 (1Û) +14v open. * 16Sep97 anc *. measure voltage on base q604, if low check integrated IC600 (TA8850). * 15Oct97 anc *.
PHILIPS 53TP60C
White with traces (or some faint color). C554 with crack. *17Sep98 h.desk*
PHILIPS 53TP60C
Blocked When used in cable function, replace IC9 (HEF4016 for hef 4066). * 10jan97 manual info *.
PHILIPS 53TP60C
Heating transistor Blue outputs, check integrated ic210, pin 3 must have (+0.6v). * 10jan97 anc *. q357, check if there is negative voltage on pin 6 of the integrated ic350, if available, see transistor q351. * 18Sep97 anc *.
PHILIPS 53TP60C
Heating resistor R279, r261 and r262, see integrated ic210. * 10jan97 anc *. r358, r361 and r362, see transistor q351. * 18Sep97 anc *.
PHILIPS 4LC1000
No vertical sync (vert5). Check lcd panel. * 09oct96 esc *.
PHILIPS 4LC1000
Turns off by itself. Flashing lamp. * 20dec95 esc *.
PHILIPS 4CM8290
Faint red. Broken track of the 3380 (2k2) smd resistor. * Aug 95 BC *.
PHILIPS 4CM8290
The whole screen shakes when turning on. Altered 2152 capacitor (68µf). * ago 95 years old *.
PHILIPS 4CM8290
Voltages above specified Check printed trail of reg. 7415. * Dec 94 BC *. eht (excess brightness), smd resistor 3608 (1k2). * Nov 95 anc*.
PHILIPS 4CM8290
Purple screen (no green) See connector track f313 (g) starter. *oct 95 anc*.
PHILIPS 4CM8290
Gray screen (no video) See h+v/sog switch, cable or connector soldering on the board trc. * May 95 BC *.
PHILIPS 4CM8290
Cyan screen (no red) = red1 Cold solder (intermittent) on transistor 7203. * Jul 95 anc*
PHILIPS 4CM8290
Yellow screen (no blue) Coil 5303 open, can also cause intermittence