☰

Philips Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philips
Results: 14238
Make Model Symptom Problem Solution By
PHILIPS 53TP60C
Convex frame ) (. Check capacitor c820 (4.7µf/10v) open, see also c450 (10µf/50v). * 15Oct97 anc *.
PHILIPS 53TP60C
Concave framework ( ). Verificar capacitor c453 (3,3nf). * 15out97 anc *.
PHILIPS 53TP60C
Frame sparkling with expanding "bloom". Check capacitor c907 smd (0.015) cracked. * 10jan97 anc*. adjust r551, if frame decreases, check integrated IC600 (TA8850N). * 25Aug97 anc *.
PHILIPS 53TP60C
Searches but cannot find (barr3/sint3). Check adjustment of coil l202 (see page 4 of the manual). * 18Sep97 anc *.
PHILIPS 53TP60C
Point on the screen (any color) Yellow point, failure in the deflection circuit, causing burns in the blue cannon. *20Aug96 anc*
PHILIPS 53TP60C
Does not hold memory (loses information). Loses information on convergence data, check integrated IC11 (x24co8p). * 11Apr96 BC *.
PHILIPS 53TP60C
Does not leave the service position. Check integrated ic11 of the convergence panel. * 10jan97 anc *.
PHILIPS 53TP60C
It doesn't work (it stays off). Check that there is no short on +12v, see ic400. * 15may96 anc check f402 (5a) +b open. * 15Aug96 BC *. check the power on line of the ic301, it should vary from 5v to 0v on pin 11 when turned on on the panel or on on the remote control, case
PHILIPS 53TP60C
Does not enter service mode. In convergence mode, check integrated IC12. * 18Sep97 anc*.
PHILIPS 53TP60C
No characters/menu appear. Check ic14 on convergence panel, comb panel filter, ic600(yc processor), ic308(character generator), IC301 (microprocessor). * 12Aug99 anc *.
PHILIPS 53TP60C
Does not adjust conv. red (i) "vert. red". Check welding of q306. *22Aug97 anc*. compressed, check resistors r311 and r32 changed to lower value. *22Aug97 anc*.
PHILIPS 53TP60C
Does not adjust with. red (-) "hot. red". Horizontal red: check r361 and r362 changed (5.1v). * 04Jul96 ac *. horizontal red, see cold solder q356. * 05nov96 anc *.
PHILIPS 53TP60C
Does not adjust conv. green (i) "vert. green". Check welding of q106 and q107. *22Aug97 anc*.
PHILIPS 53TP60C
Does not adjust conv. green (-) "hor. green". Check integrated IC110 (N5532). * 18Sep97 anc *.
PHILIPS 53TP60C
Does not adjust conv. blue (i) "vert. blue". Check the heatsinks for heat, if very hot possible integrated IC210 (measure pin 3 with 0.6v * 10jan97 anc*. check possible cold welds in q207 and q208. * 22Aug97 anc*.
PHILIPS 53TP60C
Does not adjust conv. blue (-) "hor. blue". See possible cold welds on the q257. *22Aug97 anc*.
PHILIPS 53TP60C
Does not accept remote commands Check integrated ic301 (613029). * 18Sep97 anc *.
PHILIPS 53TP60C
Horizontal lines (bottom or top). Check aquadag cable and j540 connector. * 16Aug96 anc *. c554, retraces at the bottom and also in the middle of the screen. *17Sep98 h.desk*
PHILIPS 53TP60C
Wave interference, like wood grain. Integrated ic11 (x24c08p), convergence problems. * 11Apr96 anc *.
PHILIPS 53TP60C
Interference in the image Check capacitor c211 smd 0.47µf leak. * 25Aug97 anc *. check if it is not caused by the convergence module, If so, check integrated IC10. * 18Sep97 anc *.