Search: philips
Results: 14252
Make Model Symptom Problem Solution By
PHILIPS 53TP60C
Does not leave the service position. Check integrated ic11 of the convergence panel. * 10jan97 anc *.
PHILIPS 53TP60C
It doesn't work (it stays off). Check that there is no short on +12v, see ic400. * 15may96 anc check f402 (5a) +b open. * 15Aug96 BC *. check the power on line of the ic301, it should vary from 5v to 0v on pin 11 when turned on on the panel or on on the remote control, case
PHILIPS 53TP60C
Does not enter service mode. In convergence mode, check integrated IC12. * 18Sep97 anc*.
PHILIPS 53TP60C
No characters/menu appear. Check ic14 on convergence panel, comb panel filter, ic600(yc processor), ic308(character generator), IC301 (microprocessor). * 12Aug99 anc *.
PHILIPS 53TP60C
Does not adjust conv. red (i) "vert. red". Check welding of q306. *22Aug97 anc*. compressed, check resistors r311 and r32 changed to lower value. *22Aug97 anc*.
PHILIPS 53TP60C
Does not adjust with. red (-) "hot. red". Horizontal red: check r361 and r362 changed (5.1v). * 04Jul96 ac *. horizontal red, see cold solder q356. * 05nov96 anc *.
PHILIPS 53TP60C
Does not adjust conv. green (i) "vert. green". Check welding of q106 and q107. *22Aug97 anc*.
PHILIPS 53TP60C
Does not adjust conv. green (-) "hor. green". Check integrated IC110 (N5532). * 18Sep97 anc *.
PHILIPS 53TP60C
Does not adjust conv. blue (i) "vert. blue". Check the heatsinks for heat, if very hot possible integrated IC210 (measure pin 3 with 0.6v * 10jan97 anc*. check possible cold welds in q207 and q208. * 22Aug97 anc*.
PHILIPS 53TP60C
Does not adjust conv. blue (-) "hor. blue". See possible cold welds on the q257. *22Aug97 anc*.
PHILIPS 53TP60C
Does not accept remote commands Check integrated ic301 (613029). * 18Sep97 anc *.
PHILIPS 53TP60C
Horizontal lines (bottom or top). Check aquadag cable and j540 connector. * 16Aug96 anc *. c554, retraces at the bottom and also in the middle of the screen. *17Sep98 h.desk*
PHILIPS 53TP60C
Wave interference, like wood grain. Integrated ic11 (x24c08p), convergence problems. * 11Apr96 anc *.
PHILIPS 53TP60C
Interference in the image Check capacitor c211 smd 0.47µf leak. * 25Aug97 anc *. check if it is not caused by the convergence module, If so, check integrated IC10. * 18Sep97 anc *.
PHILIPS 53TP60C
Flickering image (see serr1). Check the aquadag and j540 connection. * 16Aug96 anc *.
PHILIPS 53TP60C
Dos/menu - no color or different color. Measure +14v, possibility of r817 (1Û) being open. * 16Sep97 anc *. check transistor q603 and r609. * 25Sep97 anc *. check ic14 on convergence panel. * 12Aug99 anc *.
PHILIPS 53TP60C
Turns off immediately after turning on. Check +130v adjustment, there is a possibility of the resistor r453 is changed. * 18mar97 anc *. check starting by monitoring the secondary of t401, while turn on, if there is no voltage, pins 1 and 3 of ic402 activate protected mode, check f402 po
PHILIPS 53TP60C
Damage IC or TS semiconductor Q802, see possible changes in t801 (trans scan), with changed impedance (jsbck401). * 15Aug96 BC *. q906, see capacitor c906 smd (0.015) cracked, check resistor r934 may be open. * 10jan97 anc *. ic550, check smd capacitor
PHILIPS 53TP60C
Damages resistor Resistors r279/ r261/ r262 /r211 and r212 check integrated IC210, pin 3 (+0.6v). * 10jan97 anc *. resistor r934 opening when turned on, check if possible internal flyback sparking. *20Aug97 anc*.
PHILIPS 53TP60C
Damage fuse F2 on the convergence panel, check transistor q107 in short. * 04Jul96 ac *.