☰

Philips Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philips
Results: 14206
Make Model Symptom Problem Solution By
PHILIPS 53TP60C
Does not adjust conv. green (i) "vert. green". Check welding of q106 and q107. *22Aug97 anc*.
PHILIPS 53TP60C
Does not adjust conv. green (-) "hor. green". Check integrated IC110 (N5532). * 18Sep97 anc *.
PHILIPS 53TP60C
Does not adjust conv. blue (i) "vert. blue". Check the heatsinks for heat, if very hot possible integrated IC210 (measure pin 3 with 0.6v * 10jan97 anc*. check possible cold welds in q207 and q208. * 22Aug97 anc*.
PHILIPS 53TP60C
Does not adjust conv. blue (-) "hor. blue". See possible cold welds on the q257. *22Aug97 anc*.
PHILIPS 53TP60C
Does not accept remote commands Check integrated ic301 (613029). * 18Sep97 anc *.
PHILIPS 53TP60C
Horizontal lines (bottom or top). Check aquadag cable and j540 connector. * 16Aug96 anc *. c554, retraces at the bottom and also in the middle of the screen. *17Sep98 h.desk*
PHILIPS 53TP60C
Wave interference, like wood grain. Integrated ic11 (x24c08p), convergence problems. * 11Apr96 anc *.
PHILIPS 53TP60C
Interference in the image Check capacitor c211 smd 0.47µf leak. * 25Aug97 anc *. check if it is not caused by the convergence module, If so, check integrated IC10. * 18Sep97 anc *.
PHILIPS 53TP60C
Flickering image (see serr1). Check the aquadag and j540 connection. * 16Aug96 anc *.
PHILIPS 53TP60C
Dos/menu - no color or different color. Measure +14v, possibility of r817 (1Û) being open. * 16Sep97 anc *. check transistor q603 and r609. * 25Sep97 anc *. check ic14 on convergence panel. * 12Aug99 anc *.
PHILIPS 53TP60C
Turns off immediately after turning on. Check +130v adjustment, there is a possibility of the resistor r453 is changed. * 18mar97 anc *. check starting by monitoring the secondary of t401, while turn on, if there is no voltage, pins 1 and 3 of ic402 activate protected mode, check f402 po
PHILIPS 53TP60C
Damage IC or TS semiconductor Q802, see possible changes in t801 (trans scan), with changed impedance (jsbck401). * 15Aug96 BC *. q906, see capacitor c906 smd (0.015) cracked, check resistor r934 may be open. * 10jan97 anc *. ic550, check smd capacitor
PHILIPS 53TP60C
Damages resistor Resistors r279/ r261/ r262 /r211 and r212 check integrated IC210, pin 3 (+0.6v). * 10jan97 anc *. resistor r934 opening when turned on, check if possible internal flyback sparking. *20Aug97 anc*.
PHILIPS 53TP60C
Damage fuse F2 on the convergence panel, check transistor q107 in short. * 04Jul96 ac *.
PHILIPS 53TP60C
Poor clo correction. Check adjustment of width trimpot r469. * 10jan96 anc. check capacitor c453 (3.3nf). * 15Oct97 anc *.
PHILIPS 53TP60C
Colored outlines in the image (rgb). Integrated IC11 (X24C08P). * 11Apr96 BC *. check if fuse f2, if it is open check Possible short on red q107. * 04Jul96 ac *. check for possible cold soldering on power transistors, e.g.: in red see q356. *
PHILIPS 53TP60C
Commands do not work (all). Check integrated ic301 (613029). * 18Sep97 anc *.
PHILIPS 53TP60C
With list(s) in horizontal direction. Verificar capacitor smd c554 (.022) trincado. * 22ago97 anc.
PHILIPS 53TP60C
Burning or smoky smell. Being from the convergence board: resistors r279/ r261/ r262 /r211 and r212, check integrated ic210, there should be +0.6v at pin 3. *10jan97 anc*.
PHILIPS 53TP60C
Varying or intermittent brightness Check possible cold solders on the "digmod" terminals. *27Aug97 anc*.