Samsung Repair Tips
Search: samsung
Results: 3843
Results: 3843
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SAMSUNG |
UN32J4290
|
It takes a while to turn on, LED blinks, sometimes it turns on quickly | Corrupted eeprom data | Extract the data from an un43j4290 board and voilá, it no longer failed. | Davi.sls |
| SAMSUNG |
S19A300
|
Normal power on does not recognize analogue or digital video | Update memory with samsung program | Http://downloadcenter.samsung.com/content/fm/201203/20120302184541530/samsungfirmwareupdater_1.1.07_120227.exe, copy the link and paste it into ggogle, after doing this you will download a program, when you download the file run it, with the monitor connected via the vga cable to the computer note: the monitor must be on, even without an image), after a few seconds or minutes the monitor will be updated via the vga cable itself | Beto2828 dica do amigo aginaldo acima deu certo aqui |
| SAMSUNG |
UN32J4300 UN32J4000
|
Negative image after changing the board or display | Https://youtu.be/q1o26tbahpm | Valteno | |
| SAMSUNG |
PL51E450 PL51E490
|
LED flashes. Va vs voltages appear and fall | Turn on the TV without the buffer board, if the voltages stabilize, just change it | Measure the 47r resistors in the bμFfer, if you have opened the ci it is bad. measure on the x10k scale by taking the board's ground and the positive tip sliding onto the contacts wsound the screen's flat cables go. all pins of the 6 connectors give the same measurement, if any of the pins give a different measurement, the bμFfer is bad | |
| SAMSUNG |
CL21Z43MQ4XXAZ
KSCA |
Lights up stanby. of the match but it does not generate a high, it does not oscillate. | Zener diode in dz901 position of 5v1 or lack of 5 volts that feeds the epron | Replace zener or short the 5 volt line | BRITO SAT GNF |
| SAMSUNG |
UN40K6500
|
The TV turns on alternating RGB colors, the LCD panel remains in continuous high-gen mode. | T-com card with corrupt files in the ice1 24c64wp memory, rewrite the data or change the card (bn98-06787a, being used in several TV models) | RNSPTEC | |
| SAMSUNG |
T22B300LB
|
TV with stand-by on, blinking twice and stops but does not turn on | Defect on the power supply board (shorted sb3150 diode) | Replace and run for the hug. If you don't have the SB3150, you can use the NT648, RGP30D, MUR415, MUR460 or any schottky diode with a reverse current of at least 3A and a reverse peak voltage of 150V. | Tiago C. Neves |
| SAMSUNG |
UN55JU6000GXZD
|
Does not turn on, power LED is off, power supply is floating. | Cold solder on the TM801 transformer terminals. | Resoldering of all terminals of the TM801 transformer. | Osvaldo Bueno |
| SAMSUNG |
UE46C5100 BN44-00357B
|
TV keeps the relay on off (clicking) and sometimes starts up. or after heating the power supply board with a hairdryer, the TV always starts. | Change the cb801 22uf 450v at the power supply. Please note that when measuring with the capacimeter it gives 22uf. when heated it works and when cooled with liquid snow spray it stops working. | Hugo911 | |
| SAMSUNG |
UN40H4200
|
Stuck at logou, or no image | Https://www.youtube.com/watch?v=fu-vuzoqeio | Claudio Jorge Eckert Junior | |
| SAMSUNG |
PL43E400
|
Disarm go vs | Ysus in short | Q5018 fgd4536 d5116 sf10a400 q5016 irg7r313 q5014 e q5003 resitor de 15r r5023 | Ives |
| SAMSUNG |
CL-21K40MQ
|
Turn on the high voltage and return st by | Cr404s 681x2kv near the fly | BOSCO | |
| SAMSUNG |
UN49K6500AG-CURVA
|
Doesn't start. The standby LED responds to the remote control by blinking. | The board turns on tcon, but does not light back up and does not generate an image. | Defective eprom. I recorded a new one, 25q. | joaomvjr |
| SAMSUNG |
LN26B350F1
|
Doesn't start at all | Open mains input fuse and pfc power supply fet in raw qp802s (k8a60da) I put some strong ones in place, in this case I used 10nm60n I also changed the resistor rp820 0.12rx3w in this case I put one of 0.22rx3w | Replace the same ones and go for the hug (if you have it in scrap, it's better because of the quality of the parts) | orlando lott |
| SAMSUNG |
LN40C530F1M
|
Turns on, flashes standby 1 time and returns to standby again | Changing the z1021h regulator makes the power supply 1v2 | joemioalmeida (kinkas eletrônica) | |
| SAMSUNG |
UN40EH6030
|
Back light on without image | Capacitor cd6 shorted on t-com | In this case it could also be cd5, 7, 8 or others | Mariano |
| SAMSUNG |
MX-FS8000
|
Inoperative (does not turn on) | Capacitor cm806 na power supply | Tecdudu neves | |
| SAMSUNG |
UN55ES6500G
|
TV doesn't turn on | On the power supply board cs802 /22wf/50v cs805 /47wf/50v both without capacitance and cs810/47pf rusty terminal after replacing the power supply broke the TV turned on everything worked perfectly but if you turn it off the relay keeps knocking and the TV no longer turns on if you remove it From the socket, let the TV cool down, turn it on again, the problem was the Blutooch card, change it and run to hug | jorge assistencia tênica | |
| SAMSUNG |
LN32A550
|
When turning on the TV, it would turn on normally, a few minutes later, the image would disappear and only the sound would remain. | Cold solder on one of the contacts of the inverter transformer | Cold solder on one of the contacts of the inverter transformer | Eletrônica Cunha Pedrosa |
| SAMSUNG |
PL43F4000
|
A blinker doesn't turn on | 30nf capacitor | Broken weld... resoldering | Marcos |