☰

Sanyo Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: sanyo
Results: 852
Make Model Symptom Problem Solution By
SANYO CEP 6024 PG
A3 - A 20 		Doesn't leave st/ by Represents being upc simulating the start or removing the q 792 works normally + 12 volts low Sub c 564 = 1000μF
SANYO C20C BG2TXN
4PP11fb =sm2 		Does not always turn on or turns off and on again Transformer stops oscillating spontaneously interrupts or changes primary impedance + - 90 r Sub transf drive osc
SANYO C1471 H
EC1-LC96 		Doesn't start Lede goes from weak to strong R 858 =120k
SANYO CE28SW4
PT90 		Doesn't start The low supply leads to error as if it were a line transfer when connected it falls into protection led turns off Sub rp =64 =115k ou 120 k
SANYO
F 6 21 		When turning on there is sound there is no image Delay only after a minute does the image appear Sub c 363 = 330μF
SANYO CE 21 SN 4
11AK30 		Does not turn on red LED turning on flashes green Plus the apple to 11volt Aim R 817 = Paste the package
SANYO C20C BG2TXN
4PP11fb =sm2 		Does not always turn on or turns off and on again Transformer stops oscillating spontaneously interrupts or changes primary impedance + - 90 r Sub transf drive osc
SANYO C25 EF 50
EC 3 A 		When turned on, it goes into protection Sub c469 = 10μF
SANYO CE 21 SN 4
11AK30 		Does not turn on red LED turning on flashes green Plus the apple to 11volt Aim R 817 = Paste the package
SANYO
F 6 21 		When turning on there is sound there is no image Delay only after a minute does the image appear Sub c 363 = 330μF
SANYO CEP 6024 PG
A3 - A 20 		Doesn't leave st/ by Represents being upc simulating the start or removing the q 792 works normally + 12 volts low Sub c 564 = 1000μF
SANYO C25 EF 50
EC 3 A 		When turned on, it goes into protection Sub c469 = 10μF
SANYO C20 DN 4
PT11 		Doesn't start Background noise fluctuates badly at low 8 volts and does not reset Sub c 31 = 220μF
SANYO 14AT2
EC7-A 		Doesn't start St/by led flashes 4 times at intervals of 3 seconds + - Sub r869 =470k
SANYO VHR 14 - 15 16
CP 1 Sanyo 		CVBS signal output for scart without synchronisms C1605 = 470 uf 16 volts Sub c1605 = 470 μF
SANYO C20 DN 4
PT11 		Doesn't start Background noise fluctuates badly at low 8 volts and does not reset Sub c 31 = 220μF
SANYO 14AT2
EC7-A 		Doesn't start St/ by led flashes 4 times in a row at 3 second intervals + - Sub r869 =470k
SANYO CE28SW4
PT90 		Doesn't start The low supply leads to error as if it were a line transfer when connected it falls into protection led turns off Sub rp =64 =115k ou 120 k
SANYO C25 EG 35 N
EB2- A25 		Falls into protection or turns on with low power and oscillates D702 = 1n4148 with leak next to the ST/BY LED Sub d 702 = 1n4148
SANYO CTP-3771
Nãi sai do stand by R520 (120k) r521(120k)