Sharp Repair Tips

Search: sharp
Results: 1784

Make	Model	Symptom	Problem	Solution
SHARP	C-2006A	Dead	C707, c711 and/or c710
SHARP	37 AM 12 S	Expanded colored lines on the screen		C 713 = 1000μF 16 volt
SHARP	VC - A 43	Doesn't start	Power supply c 913 = 47 uf	Sub c913 = 47 μF
SHARP	54AM 12S CA1	Screen with expanded lines	C 712 = 1000uf 16 volt no capacity	Sub c712 = 1000μF 16volt
SHARP	DV 5432 S Deco 5	LED flashes green and does not turn on or takes a long time to turn on and off	R 751 = 0, the expulsion number	Sub r751 = 0,33r
SHARP	DV5432	Doesn't start	Lede verde centila	C754 = 470μF without capacity
SHARP	54AM 12S CA1	Screen with expanded lines	C 712 = 1000uf 16 volt no capacity	Sub c712 = 1000μF 16volt
SHARP	DV 5432 S Deco 5	LED flashes green and does not turn on or takes a long time to turn on and off	R 751 = 0, the expulsion number	Sub r751 = 0,33r
SHARP	VC - A 43	Doesn't start	Power supply c 913 = 47 uf	Sub c913 = 47 μF
SHARP	DV5432	Doesn't start	Green LED blinks	C754 = 470μF without capacity
SHARP	54DT25S	When turned on it oscillates out of frequency		Sub c604 = 220μF c622 = 220μF
SHARP	54DT25S	When turned on it oscillates out of frequency		Sub c604 = 220μF c622 = 220μF
SHARP	C-1453	Turned off	When placing the multitest tips between base and emitter, on the rx1 scale (tip, positive on the base) of q-707 (2sc 144) if it lights up changing channels alone while keeping the tips connected. the defect is a shorted channel sensor, or the diode comb at the micro input with a shorted diode. check this
SHARP	C -1491B	With drizzle without channels	Pin 2 of the plug (n) was unsoldered. model c-20st58 defect: no image with the screen off and beeping. The q-602 c2482 transistor was replaced, it looked good but it was the defect.
SHARP	C -1453	Blue screen with feedback lines, or red, or green	Blue q-853 c2229 r-866 18k, red q-851 r-868, green q-852 r-860.
SHARP	C 2035B	And the same defect as the previous one but this one is not processed automatically, it is easier to understand that the defect is due to aft. This TV also had the sound turned down.	Aft coil out of calibration and also the sound discriminator coil due to corrosion on the internal capacitor.
SHARP	C 20R12	Blue screen when asked to tune it goes over the channel if you touch the volume button until the information on the screen turns green, the moment the tuning goes through the channel it stops and the image looks like it is with the a.g.c. saturated and out of sync.	Aft coil with damaged internal capacitor.
SHARP	C - 1404A	Off but the tube filament lights up there is no sound	The printed circuit track is broken due to heat, between the d-602 pin and the c-630 pin.
SHARP	C-20ST58	No image with the screen off and beeping	The q-602 c2482 transistor was replaced, it looked good but it was the defect.
SHARP	C-1491B	Screen lights up when there is a lot of drizzle, it doesn't pick up channels	Cold solder on the circuit.