Sony Repair Tips
Search: sony
Results: 20088
Results: 20088
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
KV36FS76U
|
Sleep timer operates 2 mins too early | Mod req - ic107 pt no 680230304 | ||
| SONY |
KV3410B
|
Bu508 blown - getting hot. | Check value from supply control ( ht? ) pot to 135v rail , gone high. | ||
| SONY |
KV32WS3U
|
Faint pic, osg & sound - menu functs work but no stereo option | Eeprom corrupted - reset data & mod (sorry no info on doing this!) | ||
| SONY |
KV32DX30U
|
When replacing loptx | Don't use pt no listed in manual - wrecks crt - use part no 145330841. | ||
| SONY |
KV29X1
|
Int blank screen | Replace a board | ||
| SONY |
KV29LS30
|
Dead - led flashes 11 times | Loptr bu2515dx s/c - dry joints line dr trfmr | ||
| SONY |
KV29FL1U
|
Tripping with loptr q802 s/c | Dry joints r816 1k 3w & around line dr trfmr | ||
| SONY |
KV29F3U
|
To enter service mode | Press following buttons on remote slowly in sequence + (osd button), 5, vol+, tv and it will switch on in test mode 1 press menu on the remote next--power off to quit | ||
| SONY |
KV29F2
|
Set comes on with flyback lines then goes dead | Replace q707 (green) q710 (blue) or q704 (red) | ||
| SONY |
KV29F2
|
No sound from cold | Replace ic3 with preprogrammed new type | ||
| SONY |
KV29F1U
|
Tripping | Stops when 71v sec supply dis'd. q603 2sc3502 in prot cct leaky | ||
| SONY |
KV2964MT
|
Dead - no st/by | Avalanche diode r2k s/c, strs5941, & caps in pri psu 10µ 400v, 2µ2 350v, 47µ 63v & check for dry joints | ||
| SONY |
KV28WS2U BE3D
|
St/by led flashes twice | M24c32 sm eeprom replaced (caused by crt flashover?) | ||
| SONY |
KV28WS2U BE3D
|
Service mode entering | From st/by press osd/5/volume+/tv; tt____ will appear top right. entering tt38 sets the tv as a 28 inch, tt24 sets tv as pal i, tt79 for widescreen. menu gives submenu choices eg geometry; tt00 exits & stores | ||
| SONY |
KV28NX1U
|
Blows loptr | Dj on l803 | ||
| SONY |
KV28LS35U
|
Reverts to st/by aft initial rush of eht, led blinks twice | Over-current error caused by r618 270k in current sensing hi res | ||
| SONY |
KV28DS60U
|
Lack of width | Ps1502 1a cct prot on d1 lh vert panel (now upgraded to 2a) | ||
| SONY |
KV28DS60U
|
Electronic screwdriver settings | With set in st/by, press r/c in order - "display", "5", "vol+", "tv" - the screen now displays " t t - -". select "menu" puts you into service mode | ||
| SONY |
KV27XSC
|
No start up | Pri chopper tfmr o/c | ||
| SONY |
KV27XRTU
|
No sync | No vid i/p to sync sep pin 5 ic501. saa5230 chip on txt pcb no o/p pin 1 & overheating - q002 12v reg s/c & saa5230 faulty |