☰

Sony Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: sony
Results: 20100
Make Model Symptom Problem Solution By
SONY KV-21X5E
No image or interruption has osd Q101 = bc858
SONY KV-14LM1
5 blinkers R618 - 270k
SONY KV-M2521D
The line output transistor was very hot and the image was a little closed horizontally R822 from 1k/1w changed to 11k.
SONY KV-14LT1E
Misadjusted geometry and no sound. On channel 59 open service menu and restart nvm with tt41. If necessary, make other adjustments in the service menu.
SONY KV-M1420 - CHASSIS BE-2A
G2 high - voltage +190v on the cnc74 trc plug with the same value as the g2 trc input (pin 9) Open 27Ω r723
SONY KV-M2100E
BE2A 		Wide horizontal, it is not possible to make the correction and with the effect )( R804 (smd) with cold solders, located next to the flyback jvidal
SONY KV2160B
LED flashing and sound ok, screen dark Ic 682, regulator of 9 volts ruim.
SONY KV-29FS100
Turns on, sets to high and turns off and the LED flashes twice C514 changed
SONY KP-41T65
Screen with convergence problem Change the convergence stk`s and that's it.
SONY KV2970T
The image is distorted in a/v, that is, I put the DVD in and the image appears as if it had waves, the synchronization is a little off. warping in the middle of the screen Check c324, c326, c583 of the pin 14 output of the ic581 and the r575, all smd and the image was good.
SONY KV2070
Turning off Change 10k smd in overvoltage protection circuit r533 and d548
SONY MHC-RG66T
Cd radio deck inoperative R951 1r open
SONY BA-5D
BA-5D 		Image flickers at the top of the screen or is distorted. in the center down normal. It's as if the timing at the top was almost floating, twisting towards the right side, trying to give a headwind Retire o capacitor c582 de 1mf do pino 35 do ic301.
SONY BA-5D
BA-5D 		Buzzing with the volume turned down Earth deficiency in pci gk. this only in gk with suffix 13 Remove jumper jw16, remove jumper jw651 and add a jumper with a wire from the negative of c651 to the negative of c618 and to pin 2 of the cn1601 connector. This only applies to the GK plate with sμFfix 13, those with sμFfix 21 do not have this defect.
SONY AA-2W
AA-2W 		Distorted image at the top, like wind or as if there were scratches at the top, as a sign of noise. the image in the middle is like a gear tooth, shaky. normal sound Clean the contacts where the pp cable enters, that is, the female connector of the pp tuner with caool and the male of the cable as well. check the projection on the back cover where the pp cable passes, make sure it is not crushing or breaking the cable. If necessary, break the projection.
SONY KV-1439B/2159B/1440B -2160B
Vertical synchronism instability. the image scrolls or just shakes Eliminate q311, r315, r329, r330, r331, c329. short the r315 and c329 on the main board with a 5mm wire.
SONY BA-3B
BA-3B 		No audio Disconnect pin 46 on the computer, see if it works again. add a 12v zener between r040 (negative side) and the positive side of the zener to r268, all on pin 46. to prevent the audio IC from burning you can place a zener diode in place of the jw110 jumper, with the cathode facing towards the audio ci251 (tda2009). If there is no result when adding the zener to the PC, replace the PC or eliminate the SMD muting transistor to see if the sound returns. (except that the muting would be lost when changing channels).
SONY BA-3B
BA-3B 		Turns off by itself, volume and channel switching do not work, or it could be one of these isolated defects Change the cf001 crystal. ( attention The 2sc4834 transistor is irreplaceable, insert original. 2sc4034 is not compatible, it is printed wrong on the schematic).
SONY KV-2158B/62/63S/KV-1441B
Loud noises, in quieter places you can hear even more Place a covered wire between the ground terminal of resistor r505 and the positive terminal of c515. the wire must be close to the plate, do not pass over the plastic support.
SONY KV-2162/63S
If the customer complains that the TV does not have good image quality, with a lot of grain appearing, do this Change the c379/380/381 values ​​from 560pf to 270pf. If it doesn't work, remove the 680pf c382. these chapters. are located on the ic351 terminals.