Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
BE3B KV28FS0U
|
E/w dist & int width | Dry joints connector cn800 for int width - r835 27r 3w o/c for no e/w | ||
| SONY |
BE-3B KV25T1U
|
Dead, no start up | R600 39k 5w in psu (1-216-490-11) | ||
| SONY |
BE3B KV25T1U
|
No pic, sound & eht ok | R824 1k8 burnt & c815 dry joints | ||
| SONY |
BE3B KV24WSIU
|
Led flashes 6 times at sw on - no action | Could be memory problem (ic701) or dry joints tuner/multiway block connecting tuner pcb | ||
| SONY |
BE3B KV24WS1U
|
White horizonzal bars, crackling sound, led blinking sometimes 6-7 or 13 times, stuck in sby | Pin 15 (earth conn) on prescalar chip tsa 5511 or 5512 dry jointed | ||
| SONY |
BE-3B
|
Lack of width - no ew | Cct prot ps801 icpf10 o/c | ||
| SONY |
BE-3B
|
Int no chan change & sound | Dry joints ic001, 002, ra2, 3 | ||
| SONY |
BE3B
|
Line pulling on macro tapes | Replace jumper wire jw802 , mounted in loc l800 with ( 330r ) 3w res ptno 121590821 | ||
| SONY |
BE3B
|
Goes to stby after replacing ic605 7812 | Replace with original type icmct7812ct pt no. 8-759-279-76 | ||
| SONY |
BE3B
|
Clicking noise during nicam reception | TF02794R | ||
| SONY |
BE3B
|
All supply lines come up then go low ( stby ) | Check pin 9 cn001 if high set in protection mode disconnect pin if set still fails to come on replace ic002 memory chip ptn | ||
| SONY |
BE3 SERIES FE SERIES RE2 SERIES
|
Test mode entering | With tv in st/by use r/c press "osd" key, followed by "5", followed by "volume +", & finally "tv" key,(blank box).tv should power up upon pressing last key, and display "tt - -". | ||
| SONY |
BE3 KV28FX20U
|
Dead - faulty parts in standby psu | Ic5605 tny253p pt no 8-759-584-19, r5602 4r7 1/4w, pt no 1-249-389-11 | ||
| SONY |
BE3
|
Led flashes 13 times - no sound/pic | No tuner activity to micro - removed tuner & resoldered most conns | ||
| SONY |
BE3
|
Dead - no led flashes - eht briefly flashes | Loptx - hr7337 fits | ||
| SONY |
BE3
|
De sensitising the trip cct | 1k resistor from d618 cathode to deck enabled the set to work normally including the protection stages | ||
| SONY |
BE-2A KVM2151U
|
Pic flashing b&w and lines on pic | Dj on loptx earth connection | ||
| SONY |
BE2A KVM2151U
|
Dead with psu blow up | Ic601 str54041 chopper chip (use genuine), q601 bc637-16, r601 3r3 10w, r611 120k & f601 | ||
| SONY |
BE2A KVM2151U
|
Arcing loptx effect on pic with accompanying sounds | C606 in psu dry joint | ||
| SONY |
BE2A KVM2151
|
Int shut down with 300v present on chopper chip | Change str power chip |