☰

Sony Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: sony
Results: 20089
Make Model Symptom Problem Solution By
SONY SATA1
Gets only channels 100, 205, 999 All i get are channels 100, 205, 999.
SONY SATA1
Get menus, no channels I get the menus, but no channels.
SONY SATA1
Can't get satellite signal I can't get the satllite signal? - solution: use the zip code method to determine azimuth and elevation(make sure the system is connected and plugged in). you'll have to use acompass to judge the azimuth. you can use the hash marks on the dish tojud
SONY SAT1
Using vcr's with cable mouse and control-s Can the latest sony vcr's with cable mouse and control-s beused to change channels via the control-s on the dss to record multipleevents on the vcr?
SONY SAATB1
Dish location to receiver How far away should the dish be from the receiver?
SONY SAATA1
Watching c band channels Can i watch my c band channels on this system?
SONY KV9PT20
Flagging at top on tapes, r222 changed value Flagging at top of crt when playing back tapes on a vcr. found vcc on ic201/pin 30 was very low.
SONY KV32XBR96S
Intermittent shut down, replace t503 hdt The unit would intermittently shut down. the problem was caused by t503/horiz drive transformer. one of the legs on the primary side came loose and was making intermittent connection. replacement resolved problem. -hq
SONY KV32XBR90S
Thin yellow line (v) in the middle of pix, comb filter Thin yellow line in middle of picture. adjusted focus andscreen controls. crt checked ok.
SONY KV32XBR36
Dead set, t501 Set would turn on make an arcing noise and shut off. had tobe unplugged from outlet before it could be turned on again. all b+lines fed from g board checked good. no shorted or leaky componentsfound withΩeter test.
SONY KV32V16
Vertical jitters, re-dressed lead wires Vertical jitters, pix jumps.
SONY KV32V16
No power, ic101 No power, unit dead. standby and reset 5 volts ok.
SONY KV27V15
Power but no picture, replace r034 Power on, but no video/audio, timer led is blinking, no osd. all dc voltages are ok, but no vertical drive and no video, chroma or audio on set.
SONY KV27TS36
Incorrect part number of d board, npc substitution Servicer ordered replacement board a1346129a for kv-27ts36, but it was national back order. npc shipped a1346192a(kv27v10) for replacement. however, unit does not work. they found 5v line is causing this. -hq comments:
SONY KV20VM20
No reception cable connector (jack) broken Customer reported tv had snowy picture. found f connectorjack turned and was loose. analysis of set found f plug defective.no continuity between pin and socket connection, inside f plug . servicemanual exploded view pg 139, 14-2 showed f plug as pa
SONY KV20M10
Vertical jumps, replaced tuner Vertical jumps, found video signal from tuner pin 18 was too low, 1/2 volt. -
SONY KV13VM50
Flashing in picture, tuner After warm up lines would flash in picture. taping chassisanywhere would make symptom appear. sprayed tuner with freeze, pixstabilized.
SONY KV13VM20
Intermittent freezes, capstan motor Picture intermittently freezes.
SONY KV13VM20
Intermittent power on, re soldered r1807 Power supply would intermittently not oscillate.
SONY KV13M10
No picture and no functions, replace cf001 Unit has no function. checked ic101 pin 15 ok, but pin 7 has no output. checked osc pin 25, found waveform wrong and frequency.