Sony Repair Tips
Search: sony
Results: 20102
Results: 20102
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
SONY |
STRD365
|
Dead - replaced output devices | Unit was dead. found outputs q708 and 709 shorted. f902opened. | ||
SONY |
STRD365
|
No +5v - replaced shorted q951 and q802 | The unit arrived dead. | ||
SONY |
STRD1011S
|
Static noise on all functions - replaced ic404 | When using dolby pro logic modes unit had static noise soundslike bad reception on fm. problem was heat related. discovered defectiveic404 | ||
SONY |
SSM33
|
Wrong part l/r speaker grille frame | Left speaker grille frame part x49447332 is incorrect aswell as the right side x49447342. | ||
SONY |
SAW542
|
Buzz noise in audio - replaced ic681 | Buzz noise in subwoofer. found oscillation of around 100hzthroughout subwoofer circuit, caused by output ic681. | ||
SONY |
SAVA3
|
Need part number for r-ch speaker | Need part number for r-ch speaker system connector. -hq comments: the part number as per kcp is 156434211. in the futureplease send all part number requests directly to the kansas city partsdepartment thru your parts rep. | ||
SONY |
MDX100
|
Unit loads then no function | Unit powered up fine, fm functions worked properly but when amini disc was inserted unit would load but not function. the displaywouldn't change also. | ||
SONY |
MDS501
|
No record/ interm eject - replaced ic110 | Unit would not play back after recording and when toc editwas finished it would not eject. | ||
SONY |
MDS302
|
Disc won't eject - adjust mech | Unit will not eject disc. ref 119 mis aligned, will not ejectdisc. | ||
SONY |
MDS101
|
Intermittent right channel - resoldered j501 | Found j501 had cold soldered joint. | ||
SONY |
LBTG2000
|
No audio from tape - to connect cables from tape deck to main bd | Wires that lead from tape deck to main board not connected. | ||
SONY |
LBTD550
|
No am no tuning - s611 cold soldered | Unit had no selection between am and fm and no tuning. found that s611 was cold soldered. | ||
SONY |
HCDH50
|
No display/no functions - replaced q735 | No display no functions, missing 5.9volts at q735. | ||
SONY |
HCDG2000
|
Cd door won't open - resoldered s221 (cd open/close switch) | Unit would not open cd door. troubleshooting found that s221 was not soldered from manufacturer. | ||
SONY |
HCDD260
|
No audio - resoldered ic 1101 pins 7 and 36 (input l & r) | No audio output. ic1101 pins 7/36 | ||
SONY |
HCDD250
|
No left audio out - soldered no 701 on power amp board | Unit had no left audio. visual inspection found no 701 jack on power amp board not soldered from manufacturer. | ||
SONY |
HCDD1086
|
No tape motion - r538 open | Both tape decks would not run. found negative 6v on positive tape motor terminal. found series resister r538 open. | ||
SONY |
HCDC33
|
Doesn't open, deck b won't recd - realign mech,repc cable 63 | Cd player doesn' open tape b doesn't record. | ||
SONY |
HCDC33
|
Door jammed - realign cd mech | Cd door jammed, display no light on cd section. | ||
SONY |
HCD241
|
No audio headphones or speakers | Unit had no audio (relay ry801 not activated). found 5.5von pin 6 ic906. |