☰

Sony Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: sony
Results: 20100
Make Model Symptom Problem Solution By
SONY LBTD550
No power - f1211 not properly installed Unit has no power. after open case, found f1211 loose.
SONY LBTD550
No audio in right channel - repl ry1201 Unit did not have audio coming out the right channel. foundry1201 open.
SONY LBTD550
Optical pick up assy physically broken - repl fop assy After removing a case, with a visual inspect found opticdevice and spindle broken.
SONY LBT550
No power - replaced t1301 Unit has no power. troubleshooting, get a reading ontransformer t1301, found open.
SONY HCDG2000
No open cd door - loading gear b loose in unit The unit has no open cd door. a visual inspection on the cdchassis reveals that the pully assy for the loading gear b was loose andalso the loading gear b was found loose inside the unit. -solution reinstall loading gear b.
SONY HCDD550
No display - replaced q1383 No display from either fl displays.
SONY HCDC50U
Trays 3-5 won't open - re-formed mech pin ref 363 5th thru 3rd trays won't open, 1 & 2 do.
SONY HCDC33
No audio - repl ic106 No audio. found ic 106 defective does not transfer data toic103, function select.
SONY HCD241
Popping every 1- sec all modes - repl ic701 Every 20 seconds you hear a popping noise, both channels in all modes.
SONY CDPCX100
Unit not powering up - cable ref #25 shorting to chassis Found 18 pin cable on right side of unit rubbing againstcase,this cable comes from the display panel to the main baord and plugsin at connector cn401. the problem i saw was pin 18 of that connector hasa bare spot where the cable is bent. that base spo
SONY CDPC910
No optic functions - replaced flex cable ref# 54 Disc would load properly but, no optic movement to home pos.
SONY CDPC79ES
Noise in audio - replaced d213 Noise in left channel, low volume and noise in left channel.it's causing insufficient supply to the low pass and de-emphasis ic's.
SONY CDPC445
Int shuffle/play - repl optics Unit would play and after a period of time or if shuffledunit would stop. found optic weak.
SONY CDPC445
Mech noise - repl gear ref# 111 When door was either closing or opening a noise was heard.found main gear 111 broken inside where plastic stopper was.
SONY CDPC445
Optical jack mis aligned - aligned jack Optical jack misaligned in back panel making cable insertion difficult, if not impossible.
SONY CDPC245
No open/mech noise - cd mech stuck against table Unit open and makes mechanical. noise. after opening case founded mech stuck with table b.
SONY CDPC245
No open - set lever broken Unit not opening the tray. troubleshooting found gear is misaligned with tray table. after removal of table tray visual inspectionfound lever, set is broken.
SONY CDPC245
Disk skips int. - repl gear ref 66 Table would try to move and then would stop. found gearref# 66 had teeth bent or worn.
SONY CDPC245
Door wouldn't close Door would not close all the way in and wouldn't play.found main gear out of time. also found post broken off chassis.
SONY XRU220
Unilink connector will not accept unilink cable The unilink connector on the rear of the unit would not accepta unilink cable. this was a new unit, and the soldering on the connectorpins and lugs appeared to be original, indicating that this connector wasinstalled at the factory. -hq comments: it a