☰

Sony Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: sony
Results: 20077
Make Model Symptom Problem Solution By
SONY CDX6020
Skipping when outer tracks are played The customer may complain that skipping occurs when outertracks of discs are played. this may occur if the mechanism sub-chassisis bent, which makes it more difficult to maintain proper focus at theouter portions of discs.
SONY CDX5260
No power, no operation (found x502 defective) Unit had no functions (no display or power up).
SONY CDX5180
Skipping when outer tracks are played The customer may complain that skipping occurs when outertracks of discs are played. this may occur if the mechanism sub-chassisis bent, which makes it more difficult to maintain proper focus at theouter portions of discs.
SONY CDX5080
Skipping when outer tracks are played The customer may complain that skipping occurs when outertracks of discs are played. this may occur if the mechanism sub-chassisis bent, which makes it more difficult to maintain proper focus at theouter portions of discs.
SONY CDX5070
Amp remote has constant voltage Amp remote lead was constant 12v even with unit in off mode.found defective power control ic503.
SONY CDX5070
Unit does not respond to "+" key The unit would not respond to the + key. the keyswitch hada dead feel to it (no click).
SONY CDX5070
Lamps lit but no functions (found ic303 blown, traces open) The unit had no audio and no functions. only the lamps werelit. found that audio amp ic303 was blown, causing several traces in thearea of ic303 to open.
SONY CDX5070
Mechanism tries to clamp disc before disc is fully loaded Mechanism clamps before disc is loaded. found washer(ref.105) that secures down gear (ref. 107) was missing.
SONY CDX5040
Skipping when outer tracks are played The customer may complain that skipping occurs when outertracks of discs are played. this may occur if the mechanism sub-chassisis bent, which makes it more difficult to maintain proper focus at theouter portions of discs.
SONY CDX4040
Skipping when outer tracks are played The customer may complain that skipping occurs when outertracks of discs are played. this may occur if the mechanism sub-chassisis bent, which makes it more difficult to maintain proper focus at theouter portions of discs.
SONY MPKTRA
Shaded evf picture with mpk-tra When using the ccd-tr65 with a mpk-tra, a gap between theeyecup of the evf of the camera and the rear protector of the marine packmay cause shading on the evf picture. -hq comments: replace the eyecup of the evf with the spk lens assy(x-3943-699-1). to
SONY CCDV701
No e to e color Had chroma from camera block cn307 pin 3. ok at q663 base &collector. on at ic661 pin 1 on at ic661 pin 7. on at ic651 pin 44. badat all outputs of ic651. pin 8 & 9 of ic651 had wrong dc voltages. xtalx650 was not running.
SONY CCDV5000
Blows fuses, capstan flex rubs through Unit had f603 open. found that fu70 board was rubbing thecapstan motor flex cable. there was no fu insulating plate.
SONY CCDV5000
Unit dead no lcd Found q106 open, so even with ever 5v units micro (ic101) didnot detect battery in. -hq comments: ic103 is the voltage regulator ic. the voltage detectoric104/ic105 then commands q106 to switch between lithium or batteryvoltage.
SONY CCDV5
Lens needs help turning in auto focus. Lens did not have enough torque in auto focus. focus was fineif you helped it turn. did not want to replace lens for this problem.
SONY CCDTR91
At full zoom pix would not focus/increase ambient light Unit will not focus when full zoom in auto or manual mode.tried flange back adjustment. still the same problem also noticed thatthe adjustment would sometimes stop and the zoom would continue to run.would have to restart the alignment procedure.
SONY CCDTR91
Excessive chroma in evf, not adjustable/replace r805, vf68 Excessive chroma in evf, line out ok. could not adjust down toproper level.
SONY CCDTR91
No load or eject/replace ls arm assy 3-945-701-01 Unit would not load or eject tape. found center pin, whichengages ref 260 (roller, ls), was broken off of ls arm.
SONY CCDTR91
No camera e to e No camera e to e found ic604 defective.
SONY CCDTR81
Error in block diagram. On page 13 of the supplement 1 (block diagram) near the topof the page, the auto/manu sw is marked ic852 when it should be ic853.