Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
KV27TS32
|
Intermittent color, replaced ic301 | Intermittent color picture, gets dart intermittently. | ||
| SONY |
KV27S10
|
Part numbers missing from service manual, no resistor jumper | Part numbers for r651, r652 missing in service manual. can you provide these part numbers? thank you. -hq comments: these resistors are jummper wires. no resistors are use. | ||
| SONY |
KV27EXR10
|
New crt replacement 8-733-850-05, replace yoke ring magnet | This is the second report i've had on the new crtindicating that the h. stat has to be all the way to the ground to get itanywhere near converged. in one case, it was close enough that theycould use the hmc correction to get it in. in this case, he | ||
| SONY |
KV20TR23
|
Remains in stand-by mode, replaced ic101 | No power when set first turns on. after a few minutes, powerrelay clicks on but no picture or sound. | ||
| SONY |
KV19TS20
|
Intermittent snowy picture, re-soldered tuner | Intermitttent loss of channel, loss of tuning. | ||
| SONY |
KV13TR29
|
Incorrect sub for ic102 being supplied, will correct | Servicer checked the microfiche before ordering the above partand saw that a sub is listed of 9-759-186-37 (st24c02cp). they orderedthis part no., and rxed a st24c01b1. when this part is installed in theset id information, video presets, vert. centering, | ||
| SONY |
KPR53XBR15
|
Connector a6, g6 missing, see sb # 145 | On the new g boards connector a6-g6 is missing. -hq comments: please see service bulletins 145, and 216. 1. remove the wiring harness completely which goes between the connectors a-6 and g-6. these connectors are located between | ||
| SONY |
KPR53EXR15
|
Connector a6, g6 missing, see sb # 145 | On the new g boards connector a6-g6 is missing. -hq comments: please see service bulletins 145, and 216. 1. remove the wiring harness completely which goes between the connectors a-6 and g-6. these connectors are located between | ||
| SONY |
KPR46XBR15
|
Connector a6, g6 missing, see sb # 145 | On the new g boards connector a6-g6 is missing. -hq comments: please see service bulletins 145, and 216. 1. remove the wiring harness completely which goes between the connectors a-6 and g-6. these connectors are located between | ||
| SONY |
KPR46EXR15
|
Connector a6, g6 missing, see sb # 145 | On the new g boards connector a6-g6 is missing. -hq comments: please see service bulletins 145, and 216. 1. remove the wiring harness completely which goes between the connectors a-6 and g-6. these connectors are located between | ||
| SONY |
KPR46EXR15
|
Green crt arc through neck causing massive component failure | Crt arcing through neck. | ||
| SONY |
KPR46EX25
|
Intermittent shutdown, re-adjusted rv4501 | Shutdown would occur after a couple of hours, only when theantenna was connected. extensive troubleshootiong and shutdownadjustments were perforemd, abl current measured was below the 3500 uamax. specified value. | ||
| SONY |
KPR46EX25
|
Screen fading, replaced screen | Screen appears cloudy on the inside all the way to theouter edges. i have replaced about 8 to 10 of these screens lately. thisis the second screen i have replaced on this particular unit. thefirst one i sent in to the technical dept. for evaluation ab | ||
| SONY |
KP53V15
|
Picture flicks for about 3 sec, and then is ok. | Picture would flick for about 3 seconds when you first turnit on. it would pull in slightly from the side like a voltage regulationproblem. this may happen once in two days or may not happen for a week.any other reports? set returned to customer bec | ||
| SONY |
GEN-TV
|
Projection operating range | |||
| SONY |
FDL380
|
No picture raster only, re-soldered cn801/pin 11 | No picture only very bright screen and can't controlbrightness. -solutioin: missing neg 8v at cn801, pin 11, due to cold solder atflyback t601, pin 3. -hq comments: only report received on this symptom. thanks for thereport. | ||
| SONY |
FD525
|
Handle pins become loose, samples sent | One side of the handle comes loose due to metal pin workingits way back into the cabinet. | ||
| SONY |
SPPA60
|
No ogm recorded | Unit acts like it is recording, displaying that it isrecording (counts for 16 secs) but does not playback any audio. ic11,ic12 and ic15 were replaced. we can see audio through capacitor c79, onpin 15 of ic11 but not on pin 16 (input). -hq comments: th | ||
| SONY |
SPP95
|
Handset microphone low/low audio line | Unit's handset transmitted low audio to base. foundic-501/pin 30 to be 4 v, which did not allow the incoming signal to beamplified. | ||
| SONY |
SPP77
|
Handset microphone low/low audio line | Unit's handset transmitted low audio to base. foundic-501/pin 30 to be 4 v, which did not allow the incoming signal to beamplified. |