Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CDX5460
|
Would not load disc, caused by shorted d523 | Unit would not load a disc. | ||
| SONY |
CDX5270
|
Discs don't load, re-engage st lever with lever in top cover | The unit will not load discs. found that the st lever (ref.136) had become dis-engaged from the slot in the metal lever which is partof the mechanism top cover. | ||
| SONY |
CDX5270
|
Part number addition: fe601 (order p/n a-3282-000-a) | The service manual does not list a part number for the tunerfe601. | ||
| SONY |
CDX5260
|
E04 on display (cleaned grease from s301 on motor board) | E-04 on display after inserting cd. found sled at outside ofdisc. found s301 stuck (pushed in) so that micro thought sled was atcenter of disc. there seemed to be grease (black) on shaft of switch. | ||
| SONY |
CDX5260
|
Pre-amps pop during power on/off. | When unit was turned on/off, there would be a loud distorted popping sound from the pre-amp outputs. the speaker outputs were fine. found d101 and d201 were missing and appear to have never been installed at the factory. | ||
| SONY |
CDX5260
|
Will not accept cd (replace ref. # 124, p/n 3-384-888-01) | Unit would reset but would not accept cd. found that locking tab on left slider had broken, allowing slide to slip off of shafts labeled b on main chassis assy. | ||
| SONY |
CDX5260
|
Does not play cd (replace s301, p/n 1-572-467-31) | Sled is usually run all the way out. service test mode displays e-14. found the plunger on s301 stuck in. | ||
| SONY |
CDX5260
|
Cd ejects as soon as it is inserted (re-seat sensor board) | After the cd is inserted into the mech, it ejects it one second later. found the sensor board popped out from the clip in the front. | ||
| SONY |
CDX5260
|
Intermittent/erratic cd play (resolder ic2) | Unit plays cd's intermittently and when it will play, it usually will not change tracks. the sled will sometimes track in and out before driving the sled out and jamming it at the outer edge of the cd the unit then e-04's. tapping the mech an | ||
| SONY |
CDX5070
|
Discs don't load, re-engage st lever with lever in top cover | The unit will not load discs. found that the st lever (ref.136) had become dis-engaged from the slot in the metal lever which is partof the mechanism top cover. | ||
| SONY |
CDX5070
|
Part number addition: fe601 (order p/n a-3282-000-a) | The service manual does not list a part number for the tunerfe601. | ||
| SONY |
CDX5070
|
No audio & no scan auto stop in fm (replaced tuner fe601) | The unit had no fm audio (only static was heard), nor wouldthe unit stop at stations in scan mode in fm. am functions were ok. | ||
| SONY |
CDX5070
|
Intermittently turns off by itself (re-solder ic501) | The unit would intermittently turn off by itself. | ||
| SONY |
CDX5060
|
E04 on display (cleaned grease from s301 on motor board) | E-04 on display after inserting cd. found sled at outside ofdisc. found s301 stuck (pushed in) so that micro thought sled was atcenter of disc. there seemed to be grease (black) on shaft of switch. | ||
| SONY |
CDX45RF
|
No display | No display present on the remote commander. found j4 to becold soldered. | ||
| SONY |
CDX45RF
|
Changer does not respond to reset switch on hideaway unit | Unit has defective reset with the remote unit being used butworks fine with head unit on test bench. found j3 to be cold soldered. | ||
| SONY |
CCDVX3
|
Dew sensor activates intermittently/resolder fp523 pins 1-4 | Dew sensor circuit activates intermittently. both sides of the dew sensor would go to 5 volts. when failure occurred, traced to open ground circuit at fp-523 connection to cc-74 bd. | ||
| SONY |
CCDV101
|
Jammed mech, noisy after repair | The pin on the bottom of ref 353 is press-fit, and tends tocome loose. this causes it to disengage from the coaster spring, ref 356,and jam the mech. putting a drop of super-glue on the pin and pressing itback in solves the problem. however, some of thes | ||
| SONY |
CCDV101
|
Transport moves - no eject/replace capstan driver ic | Unit would load & unload. reels would not turn.capstan would lock up in 1 position. tried another motor by itself.motor would start if it was spun up on eject. motor would chatter thenstop. | ||
| SONY |
CCDTR91
|
No camera video-white saturated picture/replace ic604 | Picture was saturated white 100 fld. |