☰

Sony Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: sony
Results: 20100
Make Model Symptom Problem Solution By
SONY CCDTR77
Dead no lcd/replace flex cable w501 Camera was dead and no lcd. w501 30p flexible cable betweenlc45 and cn74 boards. was intermittent when flexed.
SONY CCDTR500
No color in e to e mode/check ct601, vc137 board Camera would play and record fine but no color in e to e mode.
SONY CCDTR4
Dead camera section/replace c133, vc84 board The vtr section of this camera worked fine, but when it wasswitched to camera function, the unit would shut down.
SONY CCDTR31
No playback video/replace q024 No playback video, record ok, put into pause, distorted video.
SONY CCDTR21
No e-e in vtr or camera/replace ic156, vs-22 When unit came in, there was no e-e video in vtr or cameramode. following video to the y process ic, ic151, i found the videosignal at pin34 (input). checked pin28 (output). measured the pins thatinvolve this operation, thought the ic was bad (ic151)
SONY CCDFX620
Hand grip broken / replace cabinet x-3941-4811 Hand grip broken from cabinet assembly.
SONY CCDFX510
Loses memory when removing main battery/check c891 When the main battery was in camera, lcd flashed as if nolithium battery was installed, but had date and time. if main battery wasremoved, memory would be lost.
SONY CCDFX510
No e to e video/replace ic709 No e to e video. some noise in viewfinder.
SONY CCDFX420
Hand grip broken/replace cabinet x-2941-786-1 Hand grip broken from cabinet assembly.
SONY CCDFX420
Camera mode will not switch on/replace s581 Will not go into the camera standby mode, vtr ok.
SONY CCDFX410
Haze of colored dots overlays pix with new cs31 After replacement of the cs31 board, the picture is distorted by an overlay of colored dots. transferring good adjustment data from thelanc computer to the camera does not cure the problem.
SONY CCDFX410
Part number for extender for ps board/use j-6082-177-a Is there a jig available to extend the ps-282 board? -hq comments: you can use extender j-6082-177-a for this purpose.
SONY CCD-TR81
Camera e to e flickering / check imager board cd-55 At first power up the unit had no e to e video. after a time it would flicker (video).
SONY GDM17SE1
Difficulty getting into alignment modes. Had difficulty aligning 2 units. (s/n 2006095) originally hadproblem getting into all alignment modes, after reset only mode five wouldnot set. (s/n 2003131) had problems getting into all alignment modesbefore reset. after reset, mode 1 returned a mode
SONY CPD1320
Distortion lines at bottom of pic or vertical jitter Customer complained of unstable bands of lighter lines anddensity about an inch off the bottom of picture. if you flex the dboard at the heat sink for ic400 you will get varying degrees of loss ofvert lin and vert jitter. the only ground for several co
SONY CPD1304
No operation, no hv, replace ic502 c-brd & r907 d-brd pwrsup Found unit with no high voltage, and no horizontal drive atq401. checking the power supply section on the d-board, i discovered r-917open. r917 is a fusible resistor for the 75v line. the real causeof the problem was a shorted ic-502. ic-502 uses the
SONY TCWR99ES
Improper speed on side b, cannot play reverse - s1001 defect Tape plays only slow speed. cannot play reverse direction.found s1001b defective.
SONY TCDD7
Random error messages displayed intermittently The unit would intermittently display error messages. thespecific error codes were random.
SONY TCDD3
Lid did not open, caused by bad capstan motor, ref. 154 Lid would not open. intermittently found capstan motordragging slightly.
SONY SPP85
Handset wouldn't ring - resolder r718 During icm's, the base would ring but the handset would not,page button worked normally. after pressing the talk button, the unit would seize the line and all functions were normal, including the ringeruntil the h.s. was placed in the cradle again. o