☰

Sony Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: sony
Results: 20100
Make Model Symptom Problem Solution By
SONY SLV750HF
Intermittent/no tuner Intermittent/no tuner. observed c652 had erupted.after replacing the cap would overheat and still had the same problem.measured 30v on the neg side of c652 coming from the junction of r811 andr812. -found: a carbon burn was found at h8 on p99(ma-144 b
SONY SLV750HF
List of error codes Unit will shut down in rewind. display shows l3802, i can'tfind a list of emergency codes in s/m. could you provide some? -hq comments:these codes should be the same as previous models. seeservice bulletin no. 181r1
SONY SLV750HF
No hi speed rewind Unit won't hi speed rewind, no remote operation, and pausecomes on when a prerecorded tape is inserted.
SONY SLV700HF
Squeal in rewind In rewind unit would int. squeal.
SONY EVC100
Program edits off by up to 7 seconds In the cue function a 1 minute segment recorded on the tapegains 5 seconds on the counter, when rewound and played back. otherfunctions normal.
SONY CCDFX520
Focus inoperative flex cable #355 Unit would not focus. tried uploading data to unit fromcomputer. still no focus.
SONY RMY118
Does not work with jerrold cable box, not compatible The rmy118 will not work with the jerrold starcom vi,dpv5-210-r1 cable box. the servicers tried three different remotes withthis box and it will not work.
SONY RMV11
Product code has been changed, see o/m Could not program the jerrold cable box with code 65 as otherremotes will do. had to use code 03 to operate the cable box. -hq comments: the code sets in this model have been changed. example: sony vhs code was always code 03. the code for sony vhs
SONY KV8AD20
No channel up/down with remote, must use rm759 Servicer found he could not change channels with the remote.all other functions worked ok. -hq comments: this unit uses the channel search/seek up/downcommand from the remote to change channels. the majority of other sonytv's use the channel up/down
SONY KV8AD10
No channel up/down with remote, must use rm759 Servicer found he could not change channels with the remote.all other functions worked ok. -hq comments: this unit uses the channel search/seek up/downcommand from the remote to change channels. the majority of other sonytv's use the channel up/down
SONY KV32XBR96S
Picture shrinks from sides and audio pops, resoldered q605 Picture would intermittently shrink on sides and audio wouldpop. tapping on g pcb would cause problem to act up.
SONY KV32XBR96S
No sound out of one speaker. main, replaced x3 board No sound on one speaker. traced problem to x3 board.
SONY KV32XBR75
Hor. output failure, see sb 161r1 Dead hor. output q-503 failed.
SONY KV32XBR70
Hor. output failure, see sb 161r1 Dead hor. output q-503 failed.
SONY KV32XBR70
Vertical pulled down, replaced c501, d500 Vertical pulled down voltage on ic500/pin 6 low.
SONY KV32XBR65
Hor. output failure, see sb 161r1 Dead hor. output q-503 failed.
SONY KV32XBR55
Hor. output failure, see sb 161r1 Dead hor. output q-503 failed.
SONY KV32XBR51
Hor. output failure, see sb 161r1 Dead hor. output q-503 failed.
SONY KV32XBR50
Hor. output failure, see sb 161r1 Dead hor. output q-503 failed.
SONY KV32XBR36
Intermittent loss of child audio, solder splash (p3) tp7 Customer complained of no audio from pip when using head-phones. found that intermittently, child tuner audio was lost. it wasvery difficult to trace out signal path from schematics, but after i faxedsvcr diagram from ctv-20 manual he was able to find