Sony Repair Tips
Search: sony
Results: 20077
Results: 20077
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CFD454
|
Headbase shown in service manual does not match actual part | Headbase shown in the service manual does not match the ac-tual part in unit. part is shown with alignment posts and hold downclips. part in unit has screw holes and a rear post. verified with twoother cfd-454s in shop. no info in sdis or any service | ||
| SONY |
STRAV19
|
Front panel availability | There are 92 units at nrc awaiting front panels. thereare 70 more units to be checked. there are 127 front panels on backorderin kcp. according to kcp front panel production has stopped for this unitand the parts may never be available. -hq comments: | ||
| SONY |
CCDV101
|
Manual iris problems when the board is replaced | After replacing the vc-67 board, the manual iris wouldfunction normally until the last point where the iris should be closed.at this point the iris would fully open. | ||
| SONY |
D180K
|
Unit does not focus, flex cable has open circuit | Unit does not focus (flex cable has open trace). movement ofthe optical assembly puts stress on the flex cable causing it to break.this is the second unit with this problem. | ||
| SONY |
ITA305
|
Unit won't reset | Customer says the unit won't reset. pushing the reset buttonhas no effect. | ||
| SONY |
ICB1000
|
Service manual is incorrect - reference numbers 14 and 15 | Illustrations on page 7 are wrong. no. 14 and 15 should bereversed. then part numbers will be correct. -hq comments: thanks for the info. the descriptions vs part numbers inthe service manual are correct. but as you mentioned, the referencenumbers 1 | ||
| SONY |
CFD460
|
Won't read toc | We have seen several units now where the disc spins, but willnot read toc. there is often an audible clicking sound coming from themechanism. the problem is caused by the laser assembly binding with thechassis holder (no. 156). to verify the problem: | ||
| SONY |
SPP65
|
Part number of battery | The part number of the handset's battery is not listed in theservice manual. -hq comments: the battery is stocked at kcps under the part numberbpt16. therefore, please use this part number when ordering thebattery. a service bulletin will be issued. | ||
| SONY |
SPP55
|
Part number of battery | The part number of the handset's battery is not listed in theservice manual. -hq comments: the battery is stocked at kcps under the part numberbpt16. therefore, please use this part number when ordering thebattery. a service bulletin will be issued. | ||
| SONY |
BM815
|
Ph-901, 902 not listed in service manual | On page 25 of the bm-815 service manual it shows parts 907 and909 which correspond to 907 and 908 in the parts list: photo interruptorpc boards (s. reel and t. reel). the part numbers are 1-619-136-11 and1-620-431-11. these part numbers are for boards | ||
| SONY |
SPP115
|
Test mode procedures for base unit | The procedures for putting the base unit in test mode areunclear in the service manual. -hq comments: the correct procedures for putting the base unit in testmode are as follows:1. disconnect battery pack. 2. unplug ac adaptor. 3. connect ic-501/pin 11t | ||
| SONY |
TVP-GEN
|
No cable operation through cable box | United artists cable sends a signal periodically to the cablebox. if the cable box doesn't get a signal from the cable company, itgoes to error (sticks) to the cable company menu. with our tvs and withthe aux position you only have a signal going to th | ||
| SONY |
CCDTR4
|
Incorrect service bulletin no. cam0144r1 | Camera service bulletin no. cam0144r1 transposes the new andformer chassis assembly diagrams. the former is actually the one with thescrews while the new version has the pin. -hq comments: thanks for the information. we will issue a revision. | ||
| SONY |
CCDF55
|
Vtr section is totally inoperable | When ss-100 bd, was flexed, unit would load, unload andeject only. no dc voltages on pins 27 & 28 of ic-901, as there was novoltage on the collector of q-904. | ||
| SONY |
XM3520
|
Protector light comes on immediately upon power-on | Unit will come on but will go to protect mode right after turnon. | ||
| SONY |
KPR53EX20
|
The word video is displayed when no video is inputed, normal | Ssc field technician reports two incidents of the following:in video one mode with no signal input the on screen display remains on(with jitter of course) but will go off as soon as a signal is applied. acustomer complaint is involved. what answer do we | ||
| SONY |
KV27XBR10
|
Raster blanked, replaced q-716, and r-744 ("c" board) | No rgb outputs. confirmed picture was muted. checkedv-blanking pulse from ic-301 traced to q-716 on c board. also noticedr-744 was blown. | ||
| SONY |
KV27XBR50
|
Picture is smeared with intermittent loss of color, ic-1303 | The picture appeared to be smeared with intermittent loss ofcolor. the same sections of the picture looked negative. reportedlycaused by lightning damage. the waveform at ic-1302/pin 28 on the bboard looked good but had distorted y signal at pin 26. | ||
| SONY |
KV27HSR10
|
Horizontal output transistor shorts out, replace c-522 | Q-503 (horizontal output transistor) shorts out after beingreplaced (instantly). disconnecting q-503 collector restores 137v line.with the transistor in circuit the line goes to 0vdc. | ||
| SONY |
KV27XBR55
|
No color/cannot adjust color | No color and cannot adjust color. using remote to adjustcolor would shut unit off. |