Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CDPC400
|
Optical assembly bracket | Page 20 of the service manual (see the unidentified bracket)surrounded by reference numbers 107, 106 and 120. service bulletin no. 31indicates the part number is 4-924-445-01. an asc received the part andclaims the tabs on the right side of the drawing | ||
| SONY |
SLV50
|
No operation after some time | When the power switch is turned on, the unit works for awhile.after some time, no functions will operate. turning power off and onwill cure this problem for awhile, but will occur again sometime later. | ||
| SONY |
SLV70HF
|
No operation after some time | When the power switch is turned on, the unit works for awhile.after some time, no functions will operate. turning power off and on willcure this problem for awhile, but will occur again sometime later. | ||
| SONY |
CCDF35
|
Unit would not go into record | Unit would not go into record, tape indicator blinked. | ||
| SONY |
DTC1000ES
|
Pre-mature failure of pinch roller | Rubber pinch roller becomes dry and glazed after only 10-12months. checked with owners to make sure they were not using head clean-ing fluid to clean rubber parts. in all cases the answer was no. sampleis enclosed. -hq comments: i will forward your s | ||
| SONY |
STRGX6ES
|
Unusual grounding point problems | Unit displays unusual symptoms or problems with sound powersupplies, volume board, input select board and display board. | ||
| SONY |
GM80
|
Cracking/stress on front part of mounting bracket | The gm-80 mounting bracket is stressing and cracking. thesection mounted to the vehicle (not to xv-m8 monitor) is stressing thentearing and cracking causing xv-m8 to dislodge and drop. material is madefrom thin gauge metals which appear to become stres | ||
| SONY |
XVM8
|
Vibration damage to cabinet | Many units have stress marks, cracking and loosened mountinglugs. the 4 mounting lugs on top of monitor are recessed into the plasticcabinet without any metal substructure. we determined that installationinto a typical bus/van was proper. high vibrati | ||
| SONY |
CCDF40
|
Need for extension cable when servicing camera | Servicer has requested that extension cables be made availablefor cn-007 on (ss-86) board. the cable on the camera is very short and itis difficult to operate the camera in the dis-assembled state for thepurposes of repair. please advise if cable can b | ||
| SONY |
CCDF70
|
No auto focus in tele mode | Auto focus will not focus in tele mode. | ||
| SONY |
CCDF70
|
Service mode and adjustment information | Servicer has requested service mode and adjustment proceduresfor this camera. how is the unit put in the service mode? are the codesthe same as the v11? -hq comments: please refer to ccd-f50/f70 supplement 1. | ||
| SONY |
CCDF50
|
Service mode and adjustment information | Servicer has requested service mode and adjustment proceduresfor this camera. how is the unit put in the service mode? are the codesthe same as the v11? -hq comments: please refer to ccd-f50/f70 supplement 1. | ||
| SONY |
CCDF35
|
Mechanism locked up | Mechanical lock-up. | ||
| SONY |
CCDF35
|
Weak torque | Not enough take-up torque. | ||
| SONY |
CCDF70
|
Broken lens | Lens looked as if twisted hard - breaking stop and af blockunit. | ||
| SONY |
CDP707ESD
|
Missing part number | The part number for the rotor assembly which sits above ref.no. 926 is not listed in the service manual. -hq comments: the part number is the same as listed in the cdp-x7esdmanual. it is a-4675-324-a. | ||
| SONY |
CCDF40
|
Raggedy vertical edges on straight objects (e.g. doors) | Edges of straight lines looked like line crawl especiallyabout 1/3 center of picture. | ||
| SONY |
SL340
|
No power | Unit came in with no power on. found defective ic-001. whenremoved ic, i found pin came off and very little or no thermal compoundunderneath ic. i found three units with same problem. | ||
| SONY |
CCDV9
|
Intermittent door will not close | Intermittent door will not close. dew indicated found poorcontact at cn-001 (fp-57 board). i found two units had same problem. | ||
| SONY |
KPR41DS2
|
Line in middle of picture, cracked mirror replaced | Dealer received unit and set it up on sales floor. upon ini-tial turn on, he noticed a vertical line running from top to bottom ofpicture. upon further inspection, it was found that the mirror was crack-ed. mirror was not mounted correctly - it was sh |