Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
KV20TS20
|
Ham radio interference, troubleshooting | Ham radio using 28-21-14-7-3 mhz. when transmitting 100 wattsno problem, increasing between 400-1500 watts causes the audio to distortfrom his kv20ts20. the older kv-1712d is not affected. installed 2 ferr-ite rods 7 inches long each on ac line & 2 hi | ||
| SONY |
FH707R
|
Part number for flat connector | Cannot find service manual and therefore part number for theflat connector. -hq comments: this system is an (e) model. it consists of an st-707rtuner, tc-r707 cassette deck, ta-707 amplifier and apm606 speaker. thissystem is identical to an mhc-2000 u | ||
| SONY |
CCDF40
|
Will not load | Unit will not load. this is the third unit with this problem. | ||
| SONY |
GV8
|
Tape does not eject | Tape does not eject - timing belt breaking apart, worn teeth on the belt. | ||
| SONY |
CCDV99
|
Recording motor noise | Recording motor noise in audio even on wind cut position. | ||
| SONY |
CCDV99
|
Tape jam/no eject | Tape jam - no eject. | ||
| SONY |
EVS900
|
Tape jammed no functions | Tape jam no functions. | ||
| SONY |
CCDF40
|
To view the frame-by-frame playback picture | Frame-by-frame playback not functioning. in operationalmanual and service manual instructions to view the frame-by-frame record-ing is incorrect. | ||
| SONY |
CDPC50
|
Replacement frame assembly for cdp-c50 | Support post for gear (loading c) is not part of replacementframe assembly. the frame requires replacement when the post holding partno. 61 set lever breaks. rather than undergoing the monumental task ofreplacing this entire assembly, only to have to m | ||
| SONY |
CCDF70
|
No power/no display | Unit had no power and no display. | ||
| SONY |
CCDTR5
|
No zoom function | Resistance of zoom motor measured to be 73kΩ. | ||
| SONY |
SPP80
|
Static during conversation | Middle of conversation static could be heard and then cutoff.intermittent in nature. also applies to serial number 122135. | ||
| SONY |
KPR41DS2
|
Vertical shadow on the screen, screen was mounted reversed | When viewing picture from any angle, a shadow would appearvertically from top to bottom vertically. if you viewed set directly fromthe front, the screen was clear. the cause of the problem was the screenwas mounted (inside out). how it got that way i | ||
| SONY |
KV2093R
|
On-screen display made picture dim, ic-104 | Anytime set displayed on-screen display the brightness levelof the picture would go very dark. as soon as on-screen display dis-appeared, picture brightness was normal. | ||
| SONY |
KV1326R
|
Dead, replaced crt, d-513, and r-518 | D-513/r-518 were shorted on the 800 volt line. | ||
| SONY |
KV27XBR10
|
No vertical | The unit displayed white horizontal line. found r-517, d-503open still no vertical. replaced ic-500 unit ok. | ||
| SONY |
KV27HFR
|
Intermittent vertical | These units displayed intermittent vertical roll. traced toic-302 pin 4 and cu-301 video signal was low 1.9p.p - replaced c-520.i had two units with the same problem. | ||
| SONY |
ICFCS950
|
Pcb placement of ic-101 | What is the correct orientation of ic-101? the board layoutdoes not match the silkscreen. tried two different ics in each locationand did not work. -hq comments: kansas city parts does not stock the board so we could notcheck for proper layout there. | ||
| SONY |
CFS930
|
Missing part number | The part number for the part that interfaces between thefunction switch and the rubber knob which goes to the outside world is notlisted in the service manual. -hq comments: the part is reference number 55. it is hard to tell fromthe drawing. the part | ||
| SONY |
VF150K
|
(s) adaptor part number | Need part number for the (s) adaptor (46mm to 52mm). |