Toshiba Repair Tips

Search: toshiba
Results: 5617

Make	Model	Symptom	Problem	Solution	By
TOSHIBA	48L2400	It only stays on standby, red LED is on but does not turn on	Changing the 3.3 volt SMD regulator, when measured it was only 3 volts and tsound was 3.3 on another 2 regulators that could not have any voltage with the device on standby, changing the regulator close to the processor and resolved.		xande
TOSHIBA	40RV700FDA	Doesn't start at all	Shorted fuse transistors on the board reverses. tra. 7n50u and fus.802. tsound was a broken track on jumper line 854	Replace these components and good luck	flavio
TOSHIBA	40RV700	Doesn't start at all	Shorted fuse transistors on the board reverses. tra. 7n50u and fus.802. tsound was a broken track on jumper line 854	Replace these components and good luck	flavio
TOSHIBA	TV2923	Very low sound	C636 e c637 de 47ufx25v
SEMP TOSHIBA LED	DL3277I(A)	Burning the LEDs	Current on the LEDs very high 83v! the expected is 72v.	Replace the LEDs (all) or the LED bars (all) and replace the values of rp48, rp53, rp76, rp79 all from 0.47Ω to 0.50r, 2r2, 3r, 4r7. the voltage should drop to approximately 72v.	EVANDOVIANA
TOSHIBA	1488 U14	Reduced screen	Probable cause was loose r873 smd		Marcio eletronica sao carlos
TOSHIBA	1488 U14	Reduced frame and dark screen	Probable cause was loose r873 smd	I got one on the u14 board and that was it.	Marcio eletronica sao carlos
SEMP TOSHIBA	LE1958(A)	Off without voltage on the secondary	VDW951 and VDW961 shorted, burned the rw920 (2r7), the zener VDW921 (18V), transistor VW921 (1AM or 1F)	Check them all and reset.	GDP2
SEMP TOSHIBA	DL3261	Does not turn on, stand-by light is on but does not follow commands	Change regulator 1.5 volts position u174		TORMES
TOSHIBA	TV 2159	LED off, dead, nothing works	R860 near the voltage doubler cap behind it and plonto		eletronica publison natal rgn
TOSHIBA	L32D2900	Burning LED bus.	Voltage above normal at the backlight power supply output	Replace the resistors r795 and 797 (0Ω) to 1Ω and remove r796, all next to u770.	Samuel Silva
SEMP TOSHIBA	DL3277	Turns on and in 2 seconds turns off the backlight	LED changed on the bar	Do a test by placing a 1k resistor on the bar pins in position k a	Adrian Chapadão do Céu Goiás
SEMP TOSHIBA	LC3241W	Does not turn on, nor does the LED light up	Capacitors c-877/847/842/864/865/843/835
TOSHIBA	2134	Auto buzzing at the power supply. everything good, almost everything, in truth.	Capacitor de 47 160v	The capacimeter was good, as it showed 49μF. I replaced it and the power supply was silenced.
SEMP TOSHIBA	40L2400	Turns on, after a minute it turns off, returns to standby.	3.3 n805 regulator replacement	N805 regulator replacement	Rodrigo cofferi
TOSHIBA	LC3245W	Low sound, popping.	Low voltage on the headphone amp, n201, only 1.4v	I made a jumper from coil l837 to pin 8 of the ci headphone amp, n201	davi.sls
TOSHIBA	TV2123	When it turns on green screen with line of retraces then it was dark	Capacitor smd c909 na placa do cinescopio	Then remove it now it's back to normal but see the value to replace in the diagram	Antonio Neto
TOSHIBA	LC4246WDA	When activating power, the green LED lights up, but without backlight.	Measure 12v and 24 volt line, if absent, check if tsound is voltage at the NB950 photocoupler terminals. in my case it was a 510k rf905 resistor changed to less than 330k (unusual case, as normal it is changed to more and not less)		OLIBIO - ELETRONICA ESTUDIER
SEMP TOSHIBA	2134(C)SL	Turns on normally then turns off. turns it on again, turns it off sometimes until it stays on	Q706 transistor s8050 (with leakage it heats up)	Q606 transistor s8050 (with leakage it heats up)	Fernando Nascimento
SEMP TOSHIBA	40L2400	TV turns on normally after a while and turns off.	Altered 3.3 regulator.	Swap n805	Eletrônica Ideal