Toshiba Repair Tips

Search: toshiba
Results: 5591

Make	Model	Symptom	Problem	Solution	By
SEMP TOSHIBA	LC4242WDA	Does not turn on, relay continually arming and disarming.	Standby power supply with 0v at the output due to the VCC output of the ci q840 with 0v.	Component replacement: c843 (22m50v), d846 (zenner), f840 (800ma) and q840 (a6169)	Ralyson
SEMP TOSHIBA	TV2177 SL11	Inoperative, turns on in seconds in protection with vertical closed!	Burst vertical output is open d302 diode	Replace them and it works again!	Leozinho cds
SEMP TOSHIBA	TV2981 LEM 6	Only on stand by and high power supply.	Leaky qb30 transistor.		Jadson G Nascimento
SEMP TOSHIBA	TV2987JMS LEM6	Retrace lines at the top of the screen.	C308(100uf/35v) defective.	This pump up capacitor was replaced and the problem was resolved.	José Luiz Enguer Pereira
TOSHIBA	TV 2159 NFS U18	Very dark image and blurring without screen actuation	After seeing that everything was perfect, I just changed the tube and it was fine.	Picture tube	leilson lagoa de roça pb
TOSHIBA	TV2916 NMS	Does not turn on LED turns on and off the power supply only after starting.	C 819. 10uf 50v change without measuring.		Jair.cap. poço.PA
TOSHIBA	TV1482 U8	When turned on it goes to standby	Shorted tube	Replacement	Eliel Magno
SEMP TOSHIBA	G74/313D G74/313D	Blurred image	Tube socket.	Replace the same	BARRETO CRUZ
TOSHIBA	TV2999 LEM7	Weak fi signal slipping out of tune	Z130 filter close to ci 501		Bruno Niacio
SEMP TOSHIBA	TV2134	Nothing works, stationary power supply does not oscillate.	Changing the ceramic capacitor (c609 10nf) with a slight leak (2 mega) killing the voltage 18 vdc pin 4 of (ic601 strw6554a)1	This email address is being protected from spambots. You need JavaScript enabled to view it.	This email address is being protected from spambots. You need JavaScript enabled to view it.
TOSHIBA	TV2959JFS FS-8	LED goes out slowly and voltages drop.	Power supply capacitor c819 (10x50v) with low capacitance 8.6.		Eletrônica R-TEC
TOSHIBA	TV2959JFS FS-8	LED goes out slowly and voltages drop.	Power supply capacitor c819 (10x50v) with low capacitance 8.6.		Eletrônica R-TEC
TOSHIBA	TV2988LMS LEM8	Arrived with vertical closed	Replaces q301 tda9302h and its voltages do not match the pin 1 and 7 scheme, it has to give 3volts and pin 2 26.8volts and 6 27.3volts... this last one only gave 8.9volts	Check r320, c308, (d301(replace without measuring)) resolved normal vertical deflection. If it doesn't work, check q830 5v regulator that powers pin 7 of q301, see r311 and r310. If that doesn't work, see c301 may be open near the computer.	WagnerAlves
TOSHIBA	TV2987IMS LEM5	Dark screen with little brightness	R226 from 5k6 open	Replace the r226 of 5k6 with another	JADILSON
SEMP TOSHIBA	2934	TV works normally, after a few seconds it turns orange, with a lack of blue.	Please 503	Replace without measurement: because the transistor measures normal.	This email address is being protected from spambots. You need JavaScript enabled to view it.
TOSHIBA	2158 NFS U18	Completely stopped, not even the LED lights up, and the large capacitor of the primary power supply remains charged.	3w resistor open in position 860	And just replace and kiss bye bye.	clebson vale
TOSHIBA	TV2134	Image aliasing with ripple and hissing out of frequency.	C311=47pf for 160v dry and c329=4.7pf for 250v dry, both with zero capacity.	They were replaced and the TV stayed, great....!	Armando de Olimpia Elettronica EvoluSom
SEMP / TOSHIBA	CHASSIS U 8	Noise on the fly back and burning horizontal output,	Change the electrolytic capacitor (c-167) connected to pin 52 of the micro		Ademar Videira SC
TOSHIBA	TV2998(G)MS LEM4	Low sound	After checking the capacitor c449 I changed it and it didn't solve the problem so I followed the circuit from the 12 volt line to the mute transistors via q625 which also went to point 24 of the kinescope board connector, to my surprise it was the q907 open smd and that same one When the transistor comes on, it gives a blue screen.		Ed G.M.O eletronica
TOSHIBA	2958FFS FS3 ***	RGB with problem, red did not appear	I checked the RGB transistors, they were all normal, I redid the solders and lubricated the connector, after that it worked perfectly		paulo trinca