Toshiba Repair Tips
Search: toshiba
Results: 5617
Results: 5617
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| TOSHIBA |
2999
LEM8 |
Image and sound going back and forth | Flyback with leak in the cable and shorted diodes near the varicap | After replacing the flyback tfb 4210ah and the d 421 zener (5v1) and d 420 zener (4v7) diodes, the TV worked 100% again | George Luis |
| TOSHIBA |
FS FUNING
F_74/316B |
Vertical with retrace lines at the top | Exhausted capacitors | Ca02 ca33 cb23 cb27 | digital system |
| SEMP TOSHIBA |
2134 (B) SL
SK11 |
When turning on the power key, the LED flashes and goes off by hitting the relay, and with a high power supply with + 163 volts | I did some research in the power supply control circuit and found an open 2k2 resistor 604. | I replaced the voltages and it normalized and the TV looked great. | Leonardo |
| SEMP TOSHIBA |
TV2959
FS6 |
Turns on and off with the standby LED off | D440 shorted | Replace | juci |
| TOSHIBA |
40L2400
|
Inoperative, power supply killed by lightning | Nw907, vw901, vdw904, vdw908 e fuzível | paial.eletros | |
| TOSHIBA |
40L2400
|
Burning led panel | When the first series came 2r7 in position r765 | Replace with 4r7, voltage drops from 160v to 150v, more durable, | paial.eletros |
| SEMP TOSHIBA |
LC4242WDA
|
Does not turn on, relay continually arming and disarming. | Standby power supply with 0v at the output due to the VCC output of the ci q840 with 0v. | Component replacement: c843 (22m50v), d846 (zenner), f840 (800ma) and q840 (a6169) | Ralyson |
| SEMP TOSHIBA |
TV2177
SL11 |
Inoperative, turns on in seconds in protection with vertical closed! | Burst vertical output is open d302 diode | Replace them and it works again! | Leozinho cds |
| SEMP TOSHIBA |
TV2981
LEM 6 |
Only on stand by and high power supply. | Leaky qb30 transistor. | Jadson G Nascimento | |
| SEMP TOSHIBA |
TV2987JMS
LEM6 |
Retrace lines at the top of the screen. | C308(100uf/35v) defective. | This pump up capacitor was replaced and the problem was resolved. | José Luiz Enguer Pereira |
| TOSHIBA |
TV 2159 NFS
U18 |
Very dark image and blurring without screen actuation | After seeing that everything was perfect, I just changed the tube and it was fine. | Picture tube | leilson lagoa de roça pb |
| TOSHIBA |
TV2916 NMS
|
Does not turn on LED turns on and off the power supply only after starting. | C 819. 10uf 50v change without measuring. | Jair.cap. poço.PA | |
| TOSHIBA |
TV1482
U8 |
When turned on it goes to standby | Shorted tube | Replacement | Eliel Magno |
| SEMP TOSHIBA |
G74/313D
G74/313D |
Blurred image | Tube socket. | Replace the same | BARRETO CRUZ |
| TOSHIBA |
TV2999
LEM7 |
Weak fi signal slipping out of tune | Z130 filter close to ci 501 | Bruno Niacio | |
| SEMP TOSHIBA |
TV2134
|
Nothing works, stationary power supply does not oscillate. | Changing the ceramic capacitor (c609 10nf) with a slight leak (2 mega) killing the voltage 18 vdc pin 4 of (ic601 strw6554a)1 | ||
| TOSHIBA |
TV2959JFS
FS-8 |
LED goes out slowly and voltages drop. | Power supply capacitor c819 (10x50v) with low capacitance 8.6. | Eletrônica R-TEC | |
| TOSHIBA |
TV2959JFS
FS-8 |
LED goes out slowly and voltages drop. | Power supply capacitor c819 (10x50v) with low capacitance 8.6. | Eletrônica R-TEC | |
| TOSHIBA |
TV2988LMS
LEM8 |
Arrived with vertical closed | Replaces q301 tda9302h and its voltages do not match the pin 1 and 7 scheme, it has to give 3volts and pin 2 26.8volts and 6 27.3volts... this last one only gave 8.9volts | Check r320, c308, (d301(replace without measuring)) resolved normal vertical deflection. If it doesn't work, check q830 5v regulator that powers pin 7 of q301, see r311 and r310. If that doesn't work, see c301 may be open near the computer. | WagnerAlves |
| TOSHIBA |
TV2987IMS LEM5
|
Dark screen with little brightness | R226 from 5k6 open | Replace the r226 of 5k6 with another | JADILSON |