Cce Repair Tips
Search: cce
Results: 4815
Results: 4815
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
HPS-2071
34BI |
Totally inoperative, standy by off. | Ic 101 (tda 9570h) in Curto.tv did not turn on, tsound was no standby indication. | After replacing the ic 101 (tda9570), the device was ok. | clayton |
| CCE |
HPS2971
|
Dull blurry image | C213 10n /50v on pin54 of ic101 and r441 4k7 everything on the abl line takes + or less 15 days to find this defect.. | Replace without testing.. | Elias2305 |
| CCE |
HPS2007
|
Dead | Standby led d flashes and does not start, + b normal. | Transistor drive replaced, it's good to remember that the +b of this TV is 128v and not 103v, but it's only the one with the letter c. at the end | BF.COLATINO |
| CCE |
HPS 2070S
|
Doesn't start | Exit time. Shorted, replaced, checked all voltages when turned on, in 03 seconds it burned out again. | After checking better, I found the s driver transistor. horizontal short from base to emitter. | BF.COLATINO |
| CCE |
HPS-2991FS
|
Arming and disarming directly, tsound is no time to take measurements | Ci 601, tda7496s, shorted audio amplifier. | Replace without testing, c659 and c660 of 1000μF/16v. | BF.COLATINO |
| CCE |
HPS-1402B
|
Normal sound, no image, filament does not light up, no horizontal noise. | Fr401 open (+b power line to flyback). After replacing this resistor, the TV started working normally again. | Paulo - São Luís/MA | |
| TV CCE |
HPS 14-E
|
It worked normally for approximately 20 minutes and then turned off, | It was resolved with several cold solders, including on pin 1 of the flyback. | BF.COLATINO | |
| CCE |
TV-20BLK
|
Doesn't start | Fet q801- k1611 shorted sub. by k1118, the standby LED turned on, but it didn't work | So I resoldered the fr401 and the problem was resolved. | BF.COLATINO |
| CCE |
TVS-2910FS
|
Does not turn on, LED does not light, power supply is zero | Capacitor da power supply 470mf/385v seco. | Just replace it and that's it. The TV is complete. | CARLOS |
| CCE |
HPS2988
|
Vertical closed even when placing another | D410 open | Replace measure outside the plate! | asbrito |
| TV CCE |
HPS 2185SF
|
Increase and decrease volume turn off change channel | Change all touch switches on the front panel | leonardo souza costa | |
| CCE |
HPS-2971
|
When the frame increases in volume on the sides, it starts to sway | Photo coupler with leak between pins 1 and 2, and the transistor shorted smd q808 | Replace of photo coupler ic803, and q808, zener dz811.... | house eletronica ltda |
| CCE |
HPS-2088ST
|
When turned on, the LED would flash about three times and turn off, check the 103v and 16v power supplys, both low. | I replaced the 823 diode and everything worked again. | Alvanyr |
|
| CCE |
HPS2991
|
Dark band on the left side, image saturated in all directions, screen seems too busy | 18k open resistor, r401 | Replace of the same | macceletronica |
| CCE |
HPS2071
|
Turns off after 15 minutes | If you don't want a return, change everything-q802-q804-c805-c825-c829-ressolde fr401 | HP ELETRONICA | |
| CCE |
HPS2991
|
LED doesn't light up | C-816 | joelton | |
| CCE |
HPS 2002 D
|
Inoperative burnt horizontal output | I replaced the horizontal, it got hot and burned, causing resistor r411 4k7 changed value | I replaced the 4k7 resistor with 8k2, it says 6k8, the transistor behaved normally without getting too hot | adriano alex |
| CCE |
TVD2901
|
Varying the frame on the screen as if it were a power supply varying | C421 short, abl circuit | Bruske | |
| CCE |
HPS2971
|
Varying the frame on the screen as if it were a power supply varying | C421 short, abl circuit | Bruske | |
| CCE |
HPS1407
|
Cause: faulty ic 802 tl431 | klein |