Mitsubishi Repair Tips
Search: mitsubishi
Results: 1346
Results: 1346
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| MITSUBISHI |
TC2118
|
The TV turned on normally but the colors were as if it were in NTSC or PAL-N OBS. it's not palm | I replaced the x603 and x601 crystals. It didn't solve the problem. I replaced the ci m52771-asp. It didn't solve the problem. I almost went crazy. So I used it and demagnetized the tube. | With the demagnetized tube the problem was solved | otecnico |
| MITSUBISHI |
TC1418PS
|
It just stays in stand-by at +b normal voltage | R-571 amended | Replace the same value and 8r2-3w metal film | samuel leite |
| MITSUBISHI |
TC-1499
|
No image, normal sound, no characters. | No image, normal sound, increasing the screen shows the plot, does not show characters. incorrect voltage on pins 25 and 26 of ic701. defect q705 (c1740) shorted, I put a c1815 in its place. Note: c703, 704, 705, 706, 707 and 710 (1 µf) had very low capacitance and should be replaced. | ||
| MITSUBISHI |
TC-2999
|
Tv mitsubishi tc-2999 no picture, normal sound | Mitsubishi tc-2999 tv without image, normal sound, normal mat and filament. As the screen increases, retrace lines appear. does not show characters. defect r680 (100k 1/8w) open on the kinescope board. | littlecarlos | |
| MITSUBISHI |
TC 2010
|
TV starts power supply with +b very high +- 200v instead of 115 | Ci audio output short (It's a good idea to always check if there isn't even a short in the secondary) | DEBIQUE | |
| MITSUBISHI |
TC2098
....... |
Image shakes. | Open and close the lines that form the image frame and turn off the TV. | Cold solder on the vertical output IC and nearby capacitors and also resolder the chroma IC terminals. | Armando |
| MITSUBISHI |
TC-1418PS
|
Str g5653 getting very hot and burning | Diode d913 1n4148 open | Resistronic | |
| MITSUBISHI |
TC1418PS
|
I stand-by | Open t552 transformer | Dj carlinhos | |
| MITSUBISHI |
TC2098
|
The TV was dead and the stand by didn't even light up. When checking the AC power supply I found a burnt resistor colored white, red, silver, gold. (r905,0,92r) which acts as power supply protection, I replaced it and connected the TV to the protection series, then the TV didn't turn on and the protection lamp came on. it was short in the power supply, that's when I removed the (str6707) from pin 1 to pin 2, it didn't measure anything in the test, but this str was shorted, measuring both sides | I changed the str and went for the hug lol. As a precaution, change the current capacitors at the power supply to ensure complete service | ||
| MITSUBISHI |
TC1418 PS
|
When you turn it on, it seems like it's going to turn on, but it just stays on standby | R 521 (0.75r x 2 w) | Replace it | santofofo |
| MITSUBISHI |
TV 2098
|
Agc- weak with image interference. Note: very low voltage at the AGC point on the selector. | Changed the c- 124.01 ceramic capacitor, it was leaky. | jaironuness | |
| MITSUBISHI |
TC 2097
|
Dark stripe at the top of the screen and vertical retrace lines | Deficiency in vertical filtration | Replace none 453 | paulo artur rio de janeiro |
| MITSUBISHI |
TC 2099
|
No power supply, or pulsating power supply | Change optical coupler - (pc 621) | willamis noberto | |
| MITSUBISHI |
TC-2099
|
LED lights up, works, within a few seconds the power supply drops and turns off, becoming completely inoperative. | Broken tracks on the power supply primary. | Elisson Aragão | |
| MITSUBISHI |
TC1418PS
|
TV turns on and is stuck on channel 2 | Open diode at the power supply output that makes ac-off d953 | amsmariano | |
| MITSUBISHI |
TC2018PS
|
Front controls locked TV turns on + won't change channels | D953 open power supply micro ac-off | amsmariano | |
| MITSUBISHI |
TC 2118PS
|
Tv inoperative only standby on - when activating power nothing happens | Change resistor 571 = 6r8 the TV will work again. if this has already been done. change capacitor - 567 = 22uf 160v. problem solved | otecnico | |
| MITSUBISHI |
TC2010
|
There is a power supply but there is no high and with resistor 573 it heats up a lot. | I replaced the 573 ceramic capacitor and everything worked. | Alvanyr | |
| MITSUBISHI |
TC 1410
|
Doesn't start | R908 of 100r open | JD CARLINHOS | |
| MITSUBISHI |
TC 1410
|
Doesn't start. When you press the power key, the LED goes off (as if it were going to turn on). | Resistor r571 (14" 8r2, 20" 6r8 - 3w) aberto. | TecVídeo |