Search: mitsubishi
Results: 1346
Make Model Symptom Problem Solution By
MITSUBISHI TC-2098
Completely stopped, charging the power supply capacitor. R900 er905 and see if str s6707 is shorted Just to be sure, replace capacitors c905 and c906 This email address is being protected from spambots. You need JavaScript enabled to view it.
MITSUBISHI TC1492
Does not accept the power command C915 and 917 470mx35v replace @gepê
MITSUBISHI TC21S
QUE USAN O MICRO M327210 E O TDA8361
Agc doesn't work Change values ​​of c120 and c132 Do not measure but replace c120 2.2mf and c132 82pf ars
MITSUBISHI 2099
Mitsubishi tc 2099 with sound, white screen with diagonal lines (horizontal phase) Q 705 renato tranca forte
MITSUBISHI TC-1410
TV does not oscillate, press the button to turn it on, the LED goes off and comes on again Cold solder on pin 10 of the fly back and open 8r2 5w r571 Resolder and replace the resistor eletroclaudio aguas belas
MITSUBISHI TC-2018
You plug the TV into the socket and it oscillates for 3s and goes into protection mode. Protection activated Look at the most critical components such as flyback, horizontal and vertical output, if these have a bullet, measure the voltages of the 901 regulator (str f5654), if the voltages are ok, turn off the diode (953), 18.6v, the TV will turn on and oscillate normally and it will show where the defect is, in my case it was the vertical output and the IC (701), this one came from another workshop I believe it was just the vertical one, because the IC 701 had new solder, unfortunately there is a workshop that uses From this bad faith, a hug ffeet
MITSUBISHI 1418 PS
Capacitor 955 bursting and r 952 opening C 567 sold out 4.7 x 160 Replace the same urbieta
MITSUBISHI TC-2910
Vertical closed and burning horizontal exit C201 470mf/16v shorted next to ic251 Replacement paulo-maceio/al
MITSUBISHI TC-2018
TV cutting out sound and not obeying commands either on the panel or on the remote control 5v supply on the clock and date line and high vcc Check the entire power supply including the load diodes (connected to ground) the power supply must be 5v round CSOM-(066)34231060
MITSUBISHI TV-2099
Blinking led C 901
MITSUBISHI TC2910
TV with two wavy bands on the sides After measuring almost everything in the horizontal sector I found an open resistor r561 of 4 r7 It was just a matter of changing it and the TV was ready! plramos
MITSUBISHI TC-2098
Vertical closed and scratches at the top of the screen Low voltage at the power supply and burning r456 D458 shorted vertical output shorted replace these components, when opening the vertical if scratches appear on the screen at the top of the screen replace c453 it is not necessary however if you want to replace c459, c457 is optional and go for the hug ffeet
MITSUBISHI TC 1499/2099/TC20A
Normal image but with diagonal bars going up behind the image Was it worth changing the 1uf/50 c705? JUVENAL PICOS-PI
MITSUBISHI TC-2090
Does not turn on, and you can only hear the noise of the horizontal working. R-562 open Carbonari
MITSUBISHI TC 2099
Has audio but no sync Q 705 short JF ELETRONIC
MITSUBISHI TC-1409
Image with little brightness as if the tube was weak R 559 of 220k open on the abl line Replaced solved the problem NOELSON
MITSUBISHI TC-1410
The TV stays on stand by in power on, the Apga LED but the TV doesn't turn on It gives the impression that the TV is going to turn on, but the power supply keeps oscillating On standby measure the voltage on the collector q551 (voltage on standby by 114v dc) any voltage drop on this collector could be a three-component leak (q551, c573 or c572) Marcio Rossi
MITSUBISHI TC-2099
The stand-bye LED flashes, accompanied by a pulsating noise at the same intervals as the LED. Power supply capacitor - replaced power supply capacitor c907 (TV works perfectly again) Replaced power supply capacitor c907 (TV works perfectly again)
MITSUBISHI TC2098
PCB-MAIN
Vertical closed yellow line R-458 22k
MITSUBISHI TC2098
TV with a line in the middle of the screen from top to bottom C574 ​​just change it and that's it plramos