Mitsubishi Repair Tips
Search: mitsubishi
Results: 1346
Results: 1346
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| MITSUBISHI |
TC-2098
|
Image without defined colors. bad and orange image. | Cold solder at q651 on the tube plate. | General rewelding on tube plate components. | wanderpc |
| MITSUBISHI |
TC-2098
|
Closed vertical with normal sound and white stripe on the screen. | Cold welding on d451 and d452. | We resold em d451 and d452. | wanderpc |
| MITSUBISHI |
TC-2098
|
Doesn't start. stand-by LED flashing with noise on the speaker of the same frequency. | Q901 shorted, r907 burned, d907 leaky and c907 saturated. | Exchanging components and re-welding other components of the power supply. | wanderpc |
| MITSUBISHI |
TC 2098
|
No image with horizontal sync lists | Capacitor 208 de 1x50 v. | Alvanyr |
|
| MITSUBISHI |
TC-2098
|
Does not turn on and heating in the flyback area | Output h short | Tr. 2sd1877 replaced by bu2506dx | zehkah |
| MITSUBISHI |
TC 2010
|
TV working, but the sound only makes a loud hiss | Change capacitors c 305,306,303 | DEBIQUE | |
| MITSUBISHI |
TC - 2918P
|
Cushion effect | Bad - contact on q - 553. | FERNANDO S | |
| TV MITSUBISHI |
TC-1418P
|
Does not come out of standby | When plugged into the socket, the LED turns on normally and then reduces the brightness, that is, it remains on standby, no longer obeying any command. | It was resolved by replacing the horizontal drive transformer. | bf.colatino |
| TV MITSUBISHI |
TC 2018 PS
|
This TV has a 120v power supply output with 139v. I measured it on the d952, the LED lights up but the TV doesn't turn on and there is a hissing sound at the power supply. I've already turned off +b from fly back and it's still the same | Solved this TV. someone (...) placed a coil in place of the 0.22Ω precision resistor. I just removed and inserted a 0.22Ω resistor and the TV worked normally. | bf.colatino | |
| TV MITSUBISHI |
TC-2098
|
It turns out that its sound is normal and tunes the channels perfectly. | I changed the socket/socket and it started working again. | BF.COLATNO | |
| TV MITSUBISHI |
TC 1418PS
|
This television, which according to the customer was connected to the dvd watching a film, during a storm the image on the television in av disappeared, in rf the channels are normal, when activating the av the blue screen appears, if you press menu you have the sound of the dvd nothing but the image | With the change of the ic 101-m52771 asp, the television started working again with av and the normal channels, with colors, but there is one but if I connect it to the dvd it stays normal all day long, if I change it to rf it also has the normal channels, if I go back to av the image stays in black and white and the colors only return after it cools down | Resolved by changing the ic-701e101 and eeprom. | BF.COLATNO |
| MITSUBISHI |
CT-21M1 EPM
|
I didn’t memorize the channels! | After checking the r-955 which was good, the negative voltage of 30 volts was still low, I then verified that the lack of capacity of the c-962 was at the root of the problem, I just had to replace it! these components are located at the power supply power supply next to the transformer. | J.J. | |
| MITSUBISHI |
TC2098
|
Most unsafe part | Shorted image tube | SENPRETOR | |
| MITSUBISHI |
TC 1418 PS
|
It doesn't turn on, it just stays on standby | Trafo 552 open | Replace it or try to recover it | Marcos Antonio Santofofo |
| MITSUBISHI |
TC1499
|
Does not tune channel | Agc 0,0v | Your 101, replace | SENPRETOR |
| MITSUBISHI |
TC2004ST
|
Vertical closed | C405 470nf defective (goes to pin 16 of ci 101) | Replacement | CARLU´SAT |
| MITSUBISHI |
TC 2034
|
Vertical ripples | C-559 = 330 x 10 | FERNANDO S | |
| MITSUBISHI |
TC 1499
|
When turning on the TV, a normal image appears, but without color. Then, changing the channel, the color arrives. | C 617 on the run | Replace the same. (Note) wash the plate underneath with thinner using a brush, it helps a lot. | RAIO INFOSERVISE |
| TV MITSUBISHI |
TC 1409 INOPERANTE
|
Dead | This TV was completely inoperative, with no voltage at all on the secondary transformer. After changing str 6707. I found resistor 954 of 820Ω open and horizontal output bu 2506 dx shorted. | After changing, the TV started working normally again. | BF.COLATINO |
| MITSUBISHI |
TC1410
|
The power supply was low due to a low of 45v on the STB and 47v max when turned on and the TV did not oscillate even when praying hard. | Ic 951 tl431 | RAIOINFORSERVISE |