Mitsubishi Repair Tips
Search: mitsubishi
Results: 1346
Results: 1346
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| MITSUBISHI |
FP2101
|
Vertical closed, bright list in the middle of the screen | Ic 101 la76932n 7l | próton eletrônica Avelino lopes,pi | |
| MITSUBISHI |
TC2009
|
On and off. | 9 volt regulator. | Replace regulator ic251. | R-TEC Eletrônica |
| MITSUBISHI |
TC-1499 TC-2099 TC-20A
|
Just measure on a high scale, replace and that's it. | C920 with leak | Just measure on a high scale, replace and that's it. | Bruno Capozzoli |
| MITSUBISHI |
TC-1499 TC-2099 TC-20A
|
Just turn on the LED | D953 zener 6,8v | There is no point in measuring what measures as good, you have to replace it | Bruno Capozzoli |
| MITSUBISHI |
TC-20
|
Dull TV, horizontal bands behind the image, remote control accesses the menu, but does not navigate through the options | Horizontal bands, cause: c705 and c703 of 1mf x 50 volts, no brightness, cause: adjustment of the scrim screen and brightness in the TV menu, remote control accesses the menu, but does not navigate the options: there are several parallel controls that do not have the function keys | This TV was a gift from a Greek that was donated to me, after years of leaning on it I decided to touch it, when I turned it on, only a light blue screen appeared, I know that this TV has this screen protection when there was no signal, I connected it to the antenna, the image appeared, but without brightness , I acted on the screen and it showed an image, but with horizontal bands behind the image, I replaced the c705 and c703 of 1mf x 50 volts which were shorted and resolved, I bought a remote control that accessed everything except navigating the menu to adjust them, so I researched and got tips that said it included the eeprom, I remembered that this TV came with a remote control when I got it, I looked for it... I even thought I repaired it because it was defective, I went into the menu, I adjusted the brightness, color, etc. I re-adjusted the screen and blz, the parallel control did not have function keys to navigate the menu | ivan@ |
| MITSUBISHI |
TC-2098
|
Does not turn on, stand-by LED is off | Short ic901(str-s6707), res.r900/902/905 open, fuse f901 open | Replace them all, check cap.elet.c905/906/907. | jheliocavalcanti |
| MITSUBISHI |
2098
|
Warming up q901 | Change without testing c905 and c906 | kin | |
| MITSUBISHI |
TC 1418
|
Stop r571 open. | Cond.c567 of 4.7 mf x250v change the resist.r571 and the capacitor.they are together close to f. b. | kin | |
| MITSUBISHI |
TC1418
|
R571 heats up and burns out. The TV stops. | Cond.c567 of 4.7mf x 250v replace it. is along with r571 | kin | |
| MITSUBISHI |
TC-2009
|
The device has a loud noise at the power supply. | Electrolytic capacitor: c-903, main supply. | Replaces c-903, 220μF x 400v. it's ok! | Cláudio Ribeiro, TECNOSAT ELETRÔNICA E INFORMÁTICA, Jataí-Go, |
| MITSUBISHI |
2098
|
Vertical closed | Resistors 562 and 960, both 4r7 and vertical output/sms exchange | euripedescf | |
| MITSUBISHI |
TC-2009
|
Channel locked | With the control, enter the locked channel/menu/tuning/channel lock/password number and press the channel return key 4 times (the one with two arrows facing each other) | After unlocking, to tune go to automatic tuning, press and hold vol+ | paulorusso |
| TV MITSUBISHI |
TC 2009
|
Reduced image on the sides | Component wear | C 563 4k7 1600kv | Francisco Ivan Basilio - Ibiara-PB - Nova ELETRÔNICA |
| MITSUBISHI |
TC2099
|
Tips on how to trigger automatic tuning. | Menu/tuning/function/auto tune off/volume + | Wait for 5 seconds with the volume + button on the remote control pressed and the TV starts tuning by itself. | edsomvideo |
| MITSUBISHI |
TC 1410
|
When turning on, the stand by LED stays on, the power key activates and the screen flashes continuously, the power supply oscillates so that it is not possible to read it. | Open 100r resistor 908 | Matões A.Técnica | |
| MITSUBISHI |
TC1499
|
Does not light up on standby, and has no power supply voltage. | Ic901 (str s6707) with internal transistor shorted between base and emitter, replaces continued inoperative cause r900 (3.3) open, when replacing functional TV but no video with normal plot, causes c122.2mf/50v trail open on the positive terminal. | Ademir tc | |
| MITSUBISHI |
TC-2999
|
No video and dark screen, normal audio. | R652 on kinescope board changed. | Substituir r652 | NARDINHO-ALFENAS |
| MITSUBISHI |
TC1410
|
Low power supply and heating horizontal output | Deflector | carlaosbc | |
| MITSUBISHI |
TC2099
|
Locks functions | TV off, press channel + and - until it turns on | Function lock, turn it off | ELETRONICA MAURI JUNIOR |
| MITSUBISHI |
TC2010
|
Does not turn on, LED is off. | It doesn't have 5v | Bad contact on pin 9 of t901 | Evandro Estrela |