Mitsubishi Repair Tips

Search: mitsubishi
Results: 1346

Make	Model	Symptom	Problem	Solution	By
MITSUBISHI	TC1418PS	I stand-by	Open t552 transformer		Dj carlinhos
MITSUBISHI	TC2098	The TV was dead and the stand by didn't even light up. When checking the AC power supply I found a burnt resistor colored white, red, silver, gold. (r905,0,92r) which acts as power supply protection, I replaced it and connected the TV to the protection series, then the TV didn't turn on and the protection lamp came on. it was short in the power supply, that's when I removed the (str6707) from pin 1 to pin 2, it didn't measure anything in the test, but this str was shorted, measuring both sides	I changed the str and went for the hug lol. As a precaution, change the current capacitors at the power supply to ensure complete service		This email address is being protected from spambots. You need JavaScript enabled to view it.
MITSUBISHI	TC1418 PS	When you turn it on, it seems like it's going to turn on, but it just stays on standby	R 521 (0.75r x 2 w)	Replace it	santofofo
MITSUBISHI	TV 2098	Agc- weak with image interference. Note: very low voltage at the AGC point on the selector.	Changed the c- 124.01 ceramic capacitor, it was leaky.		jaironuness
MITSUBISHI	TC 2097	Dark stripe at the top of the screen and vertical retrace lines	Deficiency in vertical filtration	Replace none 453	paulo artur rio de janeiro
MITSUBISHI	TC 2099	No power supply, or pulsating power supply	Change optical coupler - (pc 621)		willamis noberto
MITSUBISHI	TC-2099	LED lights up, works, within a few seconds the power supply drops and turns off, becoming completely inoperative.	Broken tracks on the power supply primary.		Elisson Aragão
MITSUBISHI	TC1418PS	TV turns on and is stuck on channel 2	Open diode at the power supply output that makes ac-off d953		amsmariano
MITSUBISHI	TC2018PS	Front controls locked TV turns on + won't change channels	D953 open power supply micro ac-off		amsmariano
MITSUBISHI	TC 2118PS	Tv inoperative only standby on - when activating power nothing happens	Change resistor 571 = 6r8 the TV will work again. if this has already been done. change capacitor - 567 = 22uf 160v. problem solved		otecnico
MITSUBISHI	TC2010	Tsound is a power supply but tsound is no high and with resistor 573 it heats up a lot.	I replaced the 573 ceramic capacitor and everything worked.		Alvanyr
MITSUBISHI	TC 1410	Doesn't start	R908 of 100r open		JD CARLINHOS
MITSUBISHI	TC 1410	Doesn't start. When you press the power key, the LED goes off (as if it were going to turn on).	Resistor r571 (14" 8r2, 20" 6r8 - 3w) aberto.		TecVídeo
MITSUBISHI	TC-1498	Blue screen with sound	Change tube socket		This email address is being protected from spambots. You need JavaScript enabled to view it.
MITSUBISHI	TC 2099	Blinking led	C 907 e c 906		endrew
MITSUBISHI	TC1492	Correcting a small error from our friend djalma	Power supply beeping, with excess width capacitor c309 with changed capacitance, the electrolytic capacitor c306, 400v 330uf, stopped beeping and the width returned to normal	Correcting a small error from our friend djalma	Nino, eufrasio-24@hotmailcom
MITSUBISHI	FP2101	Dead	The TV was stopped, killing the power supply, when I disconnected the +b pin of the flyback the power supply was normal, it seemed to be the flyback defective, but it was the (ic 651, tda 6107jf) rgb amplifier.		silva2
MITSUBISHI	TC1492	Replaced the c309, it stopped beeping and the width returned to normal	C309 capacitor with altered capacitance	Replaced the c309, it stopped beeping and the width returned to normal	djalma milan
MITSUBISHI	TC1492	The TV works normally, the power supply keeps beeping and the image is too wide	Replaced capacitor c309 with changed capacitance		DJALMA MILAN
MITSUBISHI	TC 2099	Diagonal bars on the "interference" screen	C705 1mf/50v, micro controller region.	Capacitor replaced	This email address is being protected from spambots. You need JavaScript enabled to view it.