Panasonic Repair Tips

Search: panasonic
Results: 2911

Make	Model	Symptom	Problem	Solution	By
PANASONIC	TC 1404 A	TV works normally +or- 30 minutes later protection works by unplugging it from the socket and starts working again for a little longer and the protection activates again	C559 7n5 x1600v		Rolf Thomas This email address is being protected from spambots. You need JavaScript enabled to view it.
PANASONIC	TC-20A12	When turned on, the TV oscillated and gave normal sound, but tsound was no high voltage.	I checked everything was normal. I went to the bus and found that it did not collect the voltage from the faly back but did not emit it.	It was raw solder on the bu emitter, I resoldered it and it was fine	This email address is being protected from spambots. You need JavaScript enabled to view it.
PANASONIC	14C6	TV makes a buzzing sound at the power supply and doesn't oscillate without +b on the horizontal output	Replaced d 835 short		jaironuness
PANASONIC	TC-20A12 TZGNPAL20A12	When the TV is turned on, it has normal sound, but not the image, it oscillates but not the voltage.	Flayback kft3aa428f, and I just change it and go for the hug		This email address is being protected from spambots. You need JavaScript enabled to view it.
PANASONIC	SA-AK230	When turned on, f61 appears on the display	Dz 5808 5v6 short		Daniel
PANASONIC	TC-14A12	Tv turning off	R 631 of 560k open		Daniel
PANASONIC	TC14A10 MX5	Inoperative - after several tests, zero voltages were found on the ic 401, the power supply pins were raised and the voltages returned to normal, the TV turned on and came back with the vertical closed. The ci was replaced and it started working again.	Replace ic 401 la 7840		Jaison
PANASONIC	TC-20C4	TV without green in colors predominates red and blue	Changed at r- 330 hms on the tube plate.		jaironuness
PANASONIC	29"	TV when you turn it on it makes noise and for the LED it reduces its intensity and the power supply becomes low because you keep trying to turn it on and off it ends up working normally I would like to ask my friend for a tip!	Thanks for your attention, thanks		francisco
PANASONIC	TC-14A12	Protection	Q401 e r401		alan
PANASONIC	TC-20C7	Alloy does not oscillate, kills 90v	Ic 401 la 7837 vertical	I replaced it and it worked normally	Eronaldo
PANASONIC	TC-20C7	Turn on the relay, it keeps arming and disarming	D 817 tfd312s shorted	Changing it solved the problem	Eronaldo
PANASONIC	TC 14C1	Only connects stby led, tsound is 310v on pin 1 of str 456a	R803 150k aberto		BRUSKE
PANASONIC	TC20A12	In av the image lacks contrast and is out of focus	D630 smd on pin 42 line of micri ic601 with leakage		ARAUJO
PANASONIC	TC14D2 B6	White screen with retrace. does not reduce brightness.	Bad contact on d506	Idem	Paulo Ricardo
PANASONIC	DVD-RV31BR RV31BR	The locked motor disc does not turn	In this model, Panasonic places an anti-vibrator on the motor shaft, this system locks it (note, place WD40 on the shaft and connect a 12v power supply for 5 minutes) off the board		This email address is being protected from spambots. You need JavaScript enabled to view it.
PANASONIC	TC29KL04	Does not arm / +b drops to 15v	R520/r521	Check 95v capacitor c863, if present, replace the resistors 2r7	3PES
PANASONIC	TC-29LK05	Vertical stroke in the center.	Sem horizontal, causa c563(390nf/250v).	Replace it ok!	Luir
PANASONIC	TX-C71UR	Power supply dead and no mat	Resistance position 803 of 560 k interrupted		iveco
PANASONIC	21FJ32L	Don't tune in.	After carrying out all voltage tests, which were ok, I changed the varicap selector and the TV tuned again.		This email address is being protected from spambots. You need JavaScript enabled to view it.