Philco Repair Tips

Search: philco
Results: 4810

Make	Model	Symptom	Problem	Solution	By
PHILCO	TP2920	Loud noise from the speakers caused the screen to flicker and turn off.	Diode d909 - sb3h100 - open		JHtron
PHILCO	PH24M	Doesn't start	Only LED standbay access	Replace or rewrite eeprom	fenixtec eletronica
PHILCO	CHALEIRA ELETRôNICA GLASS 1.7L	Direct whistle	Display	Replace of the same	Eletrônica Müller
PHILCO	PH42F10 DSGWA	Without any sound.	Shorted ca2 capacitor, located in front of the audio ID	Replace capacitor. Do not leave it without it, it may generate noise in the sound.	LABOTRON
PHILCO	PH28S63D	Back light does not turn off, in st-by LEDs stay on	On the main board q1 open	Usei bc817-25 npn 45v 500ma	Ederlin
PHILCO	PH21US	TV turns on with a black band on the left side of the screen, set to service mode, but after a while it came back.	The signal was missing on pin 57 of the computer, in the afc mesh, when touching this mesh the TV made a sparking noise near the flyback, I found the c450 with one of the terminals broken and the same one cracked	Replace the c450 and the image is back to normal	Seen store
PHILCO	PH40U16DSG	Doesn't work. Sometimes the stand by LED comes on but when you start it goes back to stand by	Fet from the power supply to the digital multimeter is fine. In the analog multimeter on the x1k scale tsound is a small leak.		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	PH40U16DSG	Doesn't work. Sometimes the stand by LED comes on but when you start it goes back to stand by	Fet from the power supply to the digital multimeter is fine. In the analog multimeter on the x1k scale tsound is a small leak.		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	PH21MG	Turn on after turn off	C826 of 47uf next to q802	See also the w802 and the resistors that also cause this defect	Antônio Neto
PHILCO	PH40R86	Doesn't start	Ci ld7536	When the TV board warms up, it works when turned off, it no longer turns on, the LD7536 switch was replaced, the defect was resolved.	TECCENTER
PHILCO	PH40R86	Doesn't start	Ci ld7536	When the TV board warms up, it works when it turns off and it no longer turns on.	TECCENTER
PHILCO	PH200	Does not turn on, does not turn on standby, secondary power supply zero volts.	22 volt zd1 zener burnt out. the zener burns out because of the bad filter capacitors tc9 -tc10.	If I helped, send a $5 pix... my pix 95679782200	LOGANKLEITON
PHILCO	PH43C21P	Main board defect	Power supply all voltages ok, sus ok and it didn't turn on, standby off	Ic u802 short replaced, tv ok	Valclei R. Ribeiro
PHILCO	PTV42G52RCF	Does not turn on, just lights up on standby	Ce67 shorted (main board, close to the power supply connector)	To replace	Junior - Tecnoprom
PHILCO	PTV49F68DSWN	Only STBY, when you press ON, STBY turns off and disarms	Short c427.	Even changing all 10μF in parallel with it (c425, c426, c427, c428, c429) the image jumped, as I had another LG t-con I preferred to replace it	ZENER Serviço Técnico
PHILCO	PH21M2	Has characters, slightly darkened image without brightness	8k resistor r463, open!	Replace	Anthony
PHILCO	TP1453 *****	Power supply does not weapon	390k r909 and 2m2 r911 were open		Moizaniel
PHILCO	PH21M 2	LED blinked but didn't hold	C 437 burst even with the replacement, it didn't solve it because r470 was open, not allowing the flayback to be fed	Replace c437 next tsh the main cause of r470 1.2r	Rogério TV
PHILCO	PH32 M DTV	On LED stays green and doesn't turn on, sometimes the stand by LED turns red and turns on	Measure large regulator voltage a little low u g1084/3v3 next to ic u9		CICERO MC ELETRONICA JAU
PHILCO	TP-2054	The TV turns off the screen, restarting with a dark blue screen and white zigzag lines. Note: when we turn on the TV it works with a perfect image, but after a few seconds and sometimes minutes the fault appears intermittently.	Replace the 6n5/1kv c715 and the "headache" is over.		SW Eletrônica