Philco Repair Tips
Search: philco
Results: 4810
Results: 4810
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
PHILCO |
PH32B51DSGWA LED
|
Dark image looks like dim or burnt LEDs | 470 z 25v capacitors and 100 x 63 puffed cap | Ariel Santos | |
PHILCO |
PTV58G70RCBL
0000 |
White screen with black spot bottom right | Short display | The famous tape to remedy it lol.... ffc2 tcon connector I isolated 12 last copies; slept... good luck! | Jhone eletronica |
PHILCO |
MSP 201 PR
|
It only stays on standby, the LED is on, it doesn't turn on | Change all touch keys | Resolved | milton santos |
PHILCO |
PH32M
|
Blinking light bulbs | 24 volt power supply, it was like 22 volts | Regulator u2 replaced..to ensure I replaced optocoupler p3 (power supply board) | Maurilio |
PHILCO |
PTV40E21DSGW
|
TV works ok but when it turns off and on again tsound is no audio | My case was made software update | Update tv via usb | Adriano Silva |
PHILCO |
PH229N
|
It didn't turn on, it just turned on the LED | Change the radio/off/cd, mp3, usb, sd, pc and aux in selector switch. | ||
PHILCO |
PH24D21D LED
B |
Tuning analog and digital channels only audio without video "flat screen, menus ok" | Update, did not accept via usb, only eeprom rewrite | Eletroserv | |
PHILCO |
PH39N86DSGW
TP.MS6308 |
Backlight turns on/off | Remove rb837,rb838,rb839. | Replace rb837 of 1r5 with 3r3 and rb of 2r2 with 4r7 | Multimarcas/Acarí |
PHILCO |
PH32U20DSGW
|
Doesn't start | Powering the secondary with a 12 v x 2a power supply, the TV turned on normally, so my defect was in the primary, I found the DP202 was leaking | Replace, I took it out of scrap. | Maurilio |
PHILCO |
PH39N86DSGW
|
Does not turn on, power supply stopped | Ci position ub101 short, the schematic doesn't mark which ci it is, I didn't find information anywsound. | I put an ld7536 and it worked. optocoupler and kia431 were shorted too. | André |
PHILCO |
TV PH49F30DSGWA
|
TV turns on normally but no image bak language off | Cw825 short | marivaldo | |
PHILCO |
PH40D10DSGW
|
Locked in logo | Change u203 rom memory or rewrite | Cabeça | |
PHILCO |
PH28D27D LED
|
League without image with sound | Test it with an LED tester, the screen lights up, when it turns on, the inverter voltage goes up and then drops to 12v. | Open the screen and it will have 1 or two defective bars. | Techmix |
PHILCO |
PH21MSS
|
Turns off after 5 seconds showing a colored line above the screen | Ic301damaged vertical outlet la78141 | Replaces ic301she is good again | Reis eletrônica |
PHILCO |
PTV32G50SN
|
Image with curtain effect | CT909 capacitor with leak and shorted DT805 SMD diode | Changing the smd capacitor and the dt807 diode can use a diode with a7 nomenclature very common on t-con boards | TV CENTER GUAIBA |
PHILCO |
PME25
|
When you plug in the socket, the display keeps flashing and beeping. When you open the door, the plate and fan are activated and the beeps become very fast. | L1 changed, just change it. | Ferraz | |
PHILCO |
PH39N86DSGW
|
Standby blinking continuously | The customer didn't tell me but he probably tried to update it and corrupted the TV's memory. | Pass on the software using a pendrive formatted in .fat32 | World TV |
PHILCO |
PTV16S86D LED
|
Stby LED won't turn on blinking | Fountain pulsing | Photo of coupler position nw2 next to the transformer, when replacing the TV it worked perfectly again. | REAL ELETRON CARVALHOS MG |
PHILCO |
PH40D10DSG
|
Reduce LED current | High voltage burning leds with 156 v | Considering 50 leds in series of 3volts each 150v remove r410 from 2r2 | BOSCO |
PHILCO |
PH40U16DSG LED
|
TV does not turn on or the standby LED lights up. making clicking noises in the secondary of the power supply | Mosfet 14n25(qp401) and diode hbr3200(dp401) shorted. | I also replaced the electrolytic capacitors as a precaution. | Roger |