Philco Repair Tips
Search: philco
Results: 4775
Results: 4775
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
PHILCO |
PH42F10
|
Restarting | Keyboard keys keys | Cabeça | |
PHILCO |
TP-2920
|
Sem video no av | Causa c731 r723 | Carlos | |
PHILCO |
PH32E32D
|
Tv philco ph32e32d cutting the sound or no sound | 100ufx16v ca815 and ca804 replace solution | This TV arrived at my workshop without sound, I updated the software and resoldered the board in the audio processing area but it didn't solve the problem! So a friend gave me this tip that I want to share with you! defect, no sound or the sound is choppy! | GEMASI |
PHILCO |
PH32E32D
|
Tv philco ph32e32d cutting the sound or no sound | 100ufx16v ca815 and ca804 replace solution | GEMASI | |
PHILCO |
PH32U20
|
Doesn't start. 12 pulsating fountain | Change dp202 under the power supply heatsink. | Tec-Center | |
PHILCO |
PH32C10DSGW
|
Without activating the blacklite | LED buses with poor contact on the SMDs | Replace bus kit | Multimarcas/Acarí |
PHILCO |
PTV32G50SN
|
Backlight off, LEDs are all good. | Power supply board, defective LED driver circuit. | Electrolytic capacitor e108 with altered esr 330μF x35v 105º. | RNSPTEC |
PHILCO |
PH21SS
|
1000uf 16 or 1000uf 25v electrolytic capacitor position c564 | Naldo Eletrônica Lajes RN | ||
PHILCO |
TP 1410
PCI 016A |
TV with dark screen without image with normal OSD. | Cap 717 | Remove cap 717 and the TV returns to normal.... | Eletrônica Evolução |
PHILCO |
PH32M5 LCD
MSD1309PX |
TV turns on normally with image, sound and characters. It heats up and in a few minutes the image disappears and the sound remains (blacklite on). Change the channel and the image returns | 3 capacitors on the main board, c8, c12 and c15 | LOGAN | |
PHILCO |
PTV32D12D
|
No sound or changes with normal image | Congratulations to the first person who posted above. AC 23 capacitor shorted | After the replace, the sound worked again | Johnson |
PHILCO |
PH32E31DG
|
Sometimes it connects with an image and sometimes without | Following João Bosco and Molina's tips, I changed the LED voltage filter capacitors. as the three are in parallel I placed one of 680ufx50v horizontally and the defect stopped | Lucafer | |
PHILCO |
PCX 11000
|
Missing 12v | Burnt regulator due to shorted 5v bluetooth chopper | I connected the 5v directly to the 3.3v stepdown ci | jorge tec |
PHILCO |
PH42E53
|
Burning leds | Reduce current, on pin 5 of each driver ci tsound are two resistors, one 470k and one 330k, remove the 330k resistor from each ci | Ariel Santos | |
PHILCO |
40R86
|
Nao liga nem led standby | Changed capacitor cw926 in bad primary supply. 4.7x100v | Cw926 capacitor on bad primary supply. replacement | cesila |
PHILCO |
PVT65F80
|
Volume increases by itself | In research I found the rd008 in the key connector line wsound it has 3 resistors of 4.7k.2k2 and the third one was oxidized, I put it at 1k and solved the problem | Medeiros Barbacena MG | |
PHILCO |
PTV49E68DS
|
Logo philco calls, stays for 1 minute and hangs up | Transistor qe3 ca22e ca27, shorted | Replace qe3 and ca22 and ca27 qe3(ao3401= a19t) | Gabriel GXP |
PHILCO |
PH28C20D
|
Even after installing new LEDs, the LEDs do not light up, reversing only gives a pulse and trips. | New LEDs came with 6v. originals were 3v | Eliminate central bar by jumpering it (has no effect on the image). remove 2 2r2 resistors to reduce current from the LEDs. | Mau3000 |
PHILCO |
PH49F30DWGWAC
|
TV doesn't turn on the backlight | Changing the cw21 capacitor near the ci uw4 led controller | PAIM ELETRÔNICA | |
PHILCO |
PH49F30DWGWAC
|
TV doesn't turn on the backlight | Changing the capacitor cw21 near the ci u35 led controller | PAIM ELETRÔNICA |