Philco Repair Tips

Search: philco
Results: 4838

Make	Model	Symptom	Problem	Solution	By
PHILCO	PH800M	Led standby piscando	Short on the 3v3 line	Sd/ms/mmc card socket shorted on the 3v3 line, I looked for a short and realized it was on the card reader housing, simply cut the 3v3 line on the socket board	fabiusmax
PHILCO	PH49U32SDGW	When turned on, it turns off after 36 seconds	Software update		RoqueCipriani
PHILCO	PH20U21D LED	Does not even turn on standby	After observing that the primary power supply was oscillating, I realized that tsound was a short on the 12 v line.	C736 em curto. smd de 10μF	GR Eletronica
PHILCO	PH28T35DG PH28T35DG LED	I'm sound	Change c622 and r621 10r next ci exit.	Replace c622 and r621 10r next ci exit.	CENTRAL AUDIO E VIDEO
PHILCO	PH40D10DSGW	Does not turn on and does not turn on standby. When measuring the secondary power supply, the voltages are pulsating.	DP202 diode (SMD Shotky) with ok measurement. I replaced it with a new one and it solved the problem.		PIXEL ASSIST
PHILCO	PH39U21DSGW	Burning LED bus	Voltage of 100.6 volts drops to 95 after removing resistor rp411 (2r2)	Remove rp411 from 2r2 close to the connector of the wires that go to the bus, once this is done it drops to 95 volts....	MIGUELTV
PHILCO	GLASS	Turn on and off	Capacitor ec1 of 4.7uf 400v empty	The replace was carried out and the kettle started working again	chaleira elétrica
PHILCO	PH32F33	Nothing turns on, inoperative	Change ci tea1733 on the power supply board primary		Alex
PHILCO	PH49F30DSGWAC	Does not turn on, no standby	Changed optical coupler uw2 and ci pwn uw1 killing the voltage.	Replace both components. the ci pwn is the ld7536.	NiloTech Eletro Eletrônica
PHILCO	PH4930DSGWAC	Does not turn on, no standby	Changed optical coupler uw2 and ci pwn uw1 killing the voltage.	Replace both components. the ci pwn is the ld7536.	NiloTech Eletro Eletrônica
PHILCO	PH42E53SG	Standby on, turns on, no backlight, does not turn off power	C122 na placa tcon	Replace with one of the same size	ToniTec
PHILCO	TV PH32M LED A4	Turns on sound and normal image after a few minutes it becomes silent.	Replace c823 remove q809.		Carlos Rocha.
PHILCO	PH21SS	Reduced frame voltage of 113v low or varying	Rp551 2k tripot oxidized or open defective	I replaced it for a 2k2 because I couldn't find a 2k one and went for the hug	orlando lott
TV PHILCO DE 29	TP29C21 PCIB0004 REV.	Defect was the power supply made a noise and did not arm, it was accumulating charge d915 with leakage	Defect in the primary power supply	Era d915	CLAUDIO ROBERTO
PHILCO	PHT660N	Does not turn on, low power supply, panel off	Capacitors with esr (they measure normal on the capacimeter but the esr meter shows the defect), change without testing e1, e2, e10 e9 e11 e31 e5 e3, e21, e26 open r20		HAHNRAHN
PHILCO	PHT660N	Does not turn on, low power supply, panel off	Capacitors with esr (they measure normal on the capacimeter but the esr meter shows the defect), change without testing e1, e2, e10 e9 e11 e31 e5 e3, e21, e26 open r20		HAHNRAHN
PHILCO	PTV50D60S	Doesn't start. only flashes standby LED	Short on the main board, killing the 5v supply. By injecting voltage into the shorted line, the processor would heat up.	RTD2968 processor replacement. As tsound is no BGA soldering, it is easier to find the processor and replace it. Another solution is to replace the main board.	GABSENS
PHILCO	PTV32C30D LED	I changed the board, it kept changing colors (rgb)	On the remote control press vol+ or vol-, or menu, or pause, or exit. in my case it was the exit key to unlock. Fits various Philco models		Eletrônica Cecé. Brumadinho MG
PHILCO	PH21M SS	When it turns on, the screen flashes and turns off. The stand by LED keeps flashing	2n5551 at position q802		Rildo Aranha
PHILCO	PH39E53DS	Burned out leds	Put the new bar and reduce the LED current	Remove resistors r44,r45,r46, leaving only resistors r47er48; some chassis already come without r44	Joao Bosco Sorocaba