Philco Repair Tips

Search: philco
Results: 4810

Make	Model	Symptom	Problem	Solution	By
PHILCO	TV PH39N86 VERSãO A	TV turns on, the logo appears and then turns off	Possibly the inverter controller but I couldn't find it for purchase	Remove rb873 and rb838 and go for the hug	Marivaldo
PHILCO	PB329BT	Crackles in the sound after minutes of use on the FM function.	Defect, lack of grounding on the x2 crystal close to the fm antenna.	Solution, solder the crystal housing to the board's ground.	Eletrônica EMB
PHILCO	PH40D10DSGW	Does not turn on and no stand-by	All normal voltages except for varicap +3.3v_tu and tun_3.3v (between 3.05)	Capacitor cp205 (on the old assistance, it bumped and the solder cracked)	lucian oliveira 61991271532 DIGITAL TECH
PHILCO	PH21MSS	The LED turns on, presses power, the LED turns off and turns on again, with a hissing noise that seems to be coming from the flay-back.	Vertical output with leakage from pin 4 to 5, c829 and c601 stuffed	Replace and please God	Daniel
PHILCO	PH32E32	LED is on and won't turn on	In my case it was not the 1v8 regulator but rather the 3v3 (u805) with low voltage. I changed it and it worked ok.		Lucafer
PHILCO	PH21 M SS MA1	Power supply goes up to 20v and returns to standby	Flay back	Replace without testing	Paulo santana
PHILCO	PH40D	Turns on, works for a minute and turns off	Software update	Software update	Rodrigo cofferi
PHILCO	PH24M LED A2	Turns it on, lights up the screen, stays for a while and goes out. normal sound, LED bar off. LED bar ok.	Ci bit3251 led bar power supply controller. pin 5 works with 0 volts and it was 0.28 volts, this is the circuit protection pin (ovp)	Replace the 10k resistor that goes from pin 5 of the ci with a 3k3 resistor so that the circuit drains this small voltage to ground.	DL Eletro Caxias
PHILCO	PH39N91	Inoperative, standby off. very low power supply output voltages	Cw926 4.7mf 100v at power supply. change without measuring.	Republishing a colleague's tip	Lucas
PHILCO	PH39N91DSGWA	The remote control doesn't work	Replace capacitors c1 and c2 on the tv sensor board with 1000 micro by 16v		Marcelo
PHILCO-ITAUTEC	TPF29S4F	Cushion effect (curved horizontal, also known as cup effect)	C1706 (1uf x 100v) exhausted and with high esr.	After the replace, the image returned to normal.	Tiago C. Neves
PHILCO	PH39N92DSGWA	Turns on with sound without back light. Changing LED strips turns the image dark.	Change without measuring cw922, cw908	Replace of the aforementioned components.	arock
PHILCO	PH40U16DSG	After changing the components that were damaged in the primary, the TV returned to stand by intermittently, sometimes after minutes, sometimes hours.	Replacing up401 (rt8573)		Bruno Barbato
PHILCO	PH40R86DSGW	TV with dark image, without adequate lighting.	Main plate, second circuit rio da power supply.	Second river power supply, electrolytic capacitors, cw908 and cw922 100μF x 63v plus cw919 and cw921 470μF x 25v replaced esr.	RNSPTEC
PHILCO	PTV32B51D	Lower LED current	Removing resistors pr38 and pr37 will reduce from 58v to 52v		mario moreci
PHILCO	PH24M	I'm sound	Varicap (seletronic) defective	Replace..	Maurilio
PHILCO	PH40D10DSGW	Turns on normally, but no image	Shorted LED power supply circuit	The following components were replaced, dp401, rp404 rp425 rp426 rp405, after the replace the LED came on but with very weak brightness, after further analysis I found the rp403 1k resistor open, I replaced it and it returned to normal.	Eletrônica Mirage
PHILCO	PHT1500	Box doesn't turn on, only the battery light comes on	Defective on/off button.		BCosta
PHILCO	PH40U16DSGW LED	Off, primary and secondary power supply voltages pulsing.	In my case it was the caps. electrolytics cp202 (4.7mfd) and cp205(22mfd) in the primary power supply. I changed it and everything was fine. good luck...		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TV PH29E63D LED	No audio	Ca 24 2.2uf		Techmix