Philco Repair Tips

Search: philco
Results: 4810

Make	Model	Symptom	Problem	Solution	By
PHILCO	PCX6500	Turns on but tsound is no sound	No power supply to the sound output, the defect was the mosfet u6 inputting 12v, outputting 1.2v		Eletrônica Mirage
PHILCO	PH32M5	TV turns on with sound but no image, black light does not turn on.	Defective electrolyte capacitor in the power supply, false contact in the mosfet.	Replace c1 c2 of 50v 10μF redo critical soldering on the power supply prioritizing q14 and q15	Alka
PHILCO	PH40D10DSGW	Does not turn on LED off primary power supply shorted	Replacement of the pwm switch ci. change rp203=39k change rp205=1.5k and check and change fuse etc..		NILSON TVS
PHILCO	PH32E31DG	Decrease v of LEDs	Remove r1b9 r1b7 r1b8 from 0.20r and place another resistance in place with a value between 0.30~0.40		TV CENTER GUAIBA
PHILCO	PH39F33	Does not connect back light power supply to low led driver	Replace ci do pfc		GIOVANO ELETRONICA
PHILCO	PH32LED A2	It doesn't turn on, only the power LED is on,	In addition to not turning on, it doesn't update via usb, if the power supply is ok, regulators are ok, remove the eprom, plug it in for 1 minute, put the eprom back in, turn it on with the usb and updated already inserted, and update,	Rodrigo cofferi, I already managed to get it to turn on again, just by heating the eprom to the point of removing it, plugging it into the socket and activating power, after the reset or update	Rodrigo cofferi
PHILCO	PH32E31DG	LED off when turned on but does not light up the screen - LED bar off	Connector that powers the LEDs with poor contact - charred - clean the connector points		ELVONEUTON FRAGA
PHILCO	PH55E20DSGWA LED	No plot_ completely white screen	Ceramic cap short on pci tcon (c643)	Replace the component. no value reference. I put a 10μF	duc40rj
PHILCO	PH39E53SG	Turn on normal image after about 3 minutes, turn off the LEDs	I tried all the good bars, I tested returns ok, I removed the transistor q3 and nothing, I noticed a difference in temperature between the two ci u1 and u201 on the inverter board, I solved it by putting a heat sink and it didn't turn off anymore note: you can change the ci		Eletrônica alternativa (TEC Mijail)
PHILCO	PH40D10DSGW	Turns on, has an image, but does not turn on the backlight	Power supply board repair	Qp401-mdd14n25 shorted ; dp401-sr3200 shorted; rp427+rp426+rp425 (r330-0.33Ω) open; rp401 (220-22Ω) replaced to 20kΩ; replace all these components with the same value and run for the hug.	MARCO BORSATO MEDTEC INFORMATICA
PHILCO	PH40U16DSG	Backlight turns on without image	Shorted capacitor on the vcon board! cd8! abs	Replace of the same	Rafael Sena
PHILCO	PH29MSS	The TV turns on in service mode with bugs in the letters and characters and does not tune the channel, the volume is at maximum, it does not enter the AV and it has a child lock after turning off the TV, it goes into protection mode	I replaced the tda11145ps microprocessor and the 24c16 memory with a 21mss one and the TV was like new
PHILCO	D28D27 PH2827	The LEDs don't light up	At the power supply		Marcos
PHILCO	PCM-2051	Turns on normally, image shakes and then turns off (varies depending on scene and brightness)	Altered abl	Open smd resistor on the abl line - r707 - 1k
PHILCO	PH21M SS	Press the keyboard TV turned on without image making a noise when putting +b 115v and flayback heating up	Flayback	Replace o flat back
PHILCO	PH40D10DSG	After changing the LED kit. the logo appears and turns off	Update error	First of all, check the 3.3 v voltages on the regulators (tsound are 3 on the board) if everything is ok. update the software, (you can buy it on the free market) tip, when updating, put the pen drive with the TV unplugged, hold down the power key and plug it in, when the blue screen appears you can release the key, don't turn it off until it's finished the process	ENGETRONICA
PHILCO	PH14C VERSÃO ``C´´	Little contrast or it does not work	Vd461 1n4148 shorted close to the fly back	Replace vd461 and run to the hug	EDIVAN ELETRONICA
PHILCO	PTV43E60SN LED JUC7.820.00207831	Power supply with 12v output, oscillating between 1.2v and 17v after a lightning strike in the network	Changing ci tl431 position up2		PATRIARCA
PHILCO	PH21M SS	Screen closed and mute	Rewrite the eprom memory.		EDIVAN ELETRONICA
PHILCO	PH32B51DSGWA LED	Dark image looks like dim or burnt LEDs	470 x 25v capacitors and 100 x 63 puffed cap		Ariel Santos