☰

Philco Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philco
Results: 4838
Make Model Symptom Problem Solution By
PHILCO TV PH39F33
DSGW 		TV turns on and backlight doesn't come on Low 24v and 58v power supply 24 only had 22 58 with 49v U402 shorted and d406 18v zener shorted Marivaldo
PHILCO PH28N91DSGWA
Does not accept control C1 Remove c1 from the buttons pci Brackmann
PHILCO PH16D10DB LED
Doesn't start C723 shorted Pardal-x
PHILCO PH19M LED A
Turns off after half an hour or sooner One of the keyboard keys is flashing. Replace the defective key, or all of them. Pardal-x
PHILCO PVT24N91SA
Lower LED current Remove the 3 r300 resistors and place a 2r2 2w resistor on the fet ww802 Lowered 6v Medeiros Eletrõnica Barbacena MG
PHILCO PTV32D12
No audio Mute Remove the ra64 close to pin 10 of the lvds. GDP2
PHILCO PH29T21D
No image, backlight on Capacitor cd19 shorted on the vcon board Remove the capacitor Gabriel
PHILCO PH21C
Dark stripe on the left side C405 2k2100v Lopestv
PHILCO TP2920
Loud noise from the speakers caused the screen to flicker and turn off. Diode d909 - sb3h100 - open JHtron
PHILCO PH24M
Doesn't start Only LED standbay access Replace or rewrite eeprom fenixtec eletronica
PHILCO CHALEIRA ELETRôNICA GLASS 1.7L
Direct whistle Display Replace of the same Eletrônica Müller
PHILCO PH42F10 DSGWA
Without any sound. Shorted ca2 capacitor, located in front of the audio ID Replace capacitor. Do not leave it without it, it may generate noise in the sound. LABOTRON
PHILCO PH28S63D
Back light does not turn off, in st-by LEDs stay on On the main board q1 open Usei bc817-25 npn 45v 500ma Ederlin
PHILCO PH21US
TV turns on with a black band on the left side of the screen, set to service mode, but after a while it came back. The signal was missing on pin 57 of the computer, in the afc mesh, when touching this mesh the TV made a sparking noise near the flyback, I found the c450 with one of the terminals broken and the same one cracked Replace the c450 and the image is back to normal Seen store
PHILCO PH40U16DSG
Doesn't work. Sometimes the stand by LED comes on but when you start it goes back to stand by Fet from the power supply to the digital multimeter is fine. In the analog multimeter on the x1k scale tsound is a small leak. This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO PH40U16DSG
Doesn't work. Sometimes the stand by LED comes on but when you start it goes back to stand by Fet from the power supply to the digital multimeter is fine. In the analog multimeter on the x1k scale tsound is a small leak. This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO PH21MG
Turn on after turn off C826 of 47uf next to q802 See also the w802 and the resistors that also cause this defect Antônio Neto
PHILCO PH40R86
Doesn't start Ci ld7536 When the TV board warms up, it works when turned off, it no longer turns on, the LD7536 switch was replaced, the defect was resolved. TECCENTER
PHILCO PH40R86
Doesn't start Ci ld7536 When the TV board warms up, it works when it turns off and it no longer turns on. TECCENTER
PHILCO PH200
Does not turn on, does not turn on standby, secondary power supply zero volts. 22 volt zd1 zener burnt out. the zener burns out because of the bad filter capacitors tc9 -tc10. If I helped, send a $5 pix... my pix 95679782200 LOGANKLEITON