Philco Repair Tips

Search: philco
Results: 4811

Make	Model	Symptom	Problem	Solution	By
PHILCO	PCM 1443 EMOTION ***	Turning off white screen and retraces	R-715 c-719	R-715 1r,subs 4r7 c-719 10mf x 350v	wagner
PHILCO	TPF2130	Does not turn on, without +14v pin 1 ic905	Solda fria r931 18r 2w		BETO2828
PHILCO	PCS 2078 NãO MARCA	Bu 2508 dx shorts out	C730 5k6 1kv6 changed and change original bu 2508 dx and increase c715 to 7k5*2kv		luiztvsom
TV PHILCO	PCM 2046	Luminance-	Replaced the c716 10 / 250 volts	TV worked normally.	jaironuness
PHILCO	TP-2053	TV doesn't work std-by light blinks continuously but dimly	Changed the vertical output tda9309		jaironuness
PHILCO	TP-1452N	When turning on tsound is no sound after a while the sound starts to come back hoarse.	Change the audio output		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TP-1452	TV with normal power supply, when turned on it generates and cuts in 1 second	Check r713 of 1k8 changed		Daniel
PHILCO	PC 20R42	Interference on the screen without video TV has sound	Replace c301 0.47/35 votes		jaironuess
PHILCO	PC- 20R42 **	TV out of horizontal frequency	Or capacitor 303 of 47/35 votes was exhausted		jaironuness
PHILCO	TPF 2941	It has a power supply but no gun	It fell, it was fixed, the trails worked normally; after two days it broke down, it was left alone in the waiting room		carlos branco
PHILCO	PCM2044	When the TV was turned on, the image was shaking, and when the volume was increased, the image was even more shaky.	I checked the power supply and it was normal, but when I removed the capacitor from the power supply input I realized that it had a bad, rotten leg, the 400v/220mf c905 replaced it and went for a hug		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	PCM1443	Image blinking as if it were a stand by LED, normal frame, normal voltages, except video voltage; controls inoperative.	R713(100k) open.	Replace r713(100k), device ok.	clayton
PHILCO	TP1454	Problem with the colors, it remains without demagnetizing the kinescope.	Check the "epcos" brand component with placement number th 901. this component is connected together with the kinescope coil.	Just replace it with another one and go for the hug!!!	FRANCISCO
PHILCO	TPF-2901 CP01RL01	When turned on, it displays a white screen with horizontal retrace lines and seconds later it turns off.	Replacement of the 4r7 r711 that was open.		Marques
PHILCO	PCS 2700	The TV turns off as soon as it was turned on	This TV doesn't oscillate without the fly back and without the deflector so it would be more difficult to discover the defect.	But in this case it was the bad deflector coil that was causing the TV to turn off	heliomar
PHILCO	TPF 2130 CP 03	Does not turn on, tsound is no + 14 vdc pin 1 of ic 905	Change c 918 open		CARLOS ROCHA
PHILCO	PCS-2976	Actuated protection It is with very high voltage	C715 or c730 changed		Henry Moura
PHILCO	PCS 3322N CP 01 LR02	When turning off the power, it no longer turns on, only flashes, the power supply does not arm	Next to the wide capacitor switch c728 3n3 x 1600v	C728 3n3 x 1600v	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	PCM2976	TV turns on after + or - 30 seconds, threatens to close the horizontal and turns off.	Probable cause, open power supply diode d917.		amsmariano
PHILCO	PCM-2046	Jagged image	Interference on the kinescope PCI flat	Move the kinescope PCI flat away from the flay back as much as possible.	Wender