☰

Philco Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philco
Results: 4811
Make Model Symptom Problem Solution By
PHILCO PCM2146
... 		Tv doesn't work Blown fuse causes c-984 =4 nf 7, disc. They were replaced and the TV worked beautifully. Armando
PHILCO REAL FLAT TPF 2940
Does not turn on, noise on the horizontal output board D1701/by228 1500v shorted Replace Igor Almeida
PHILCO TP2054
Bluish image with retraction lines. Flyback Adjust the screen
PHILCO PCS 2952
It worked normally, turned off after +or- 10 minutes, normal power supply. Ic 601 ( la7833 ) saida vertical I realized that IC 601 was getting very hot, I replaced it and the TV worked normally. M&E ELETRONICA
GRADIENTE PHILCO TF2150
Black screen on +-70% of the TV in the horizontal direction and on 30% of the TV it works normally with audio and everything Enter service mode and reset which returns to normal To enter service mode, simultaneously press menu on the remote control and on the TV with the TV turned on. samuel leite
PHILCO PCS 2700
TV wobbled and cut, I noticed clear lines on the screen In this case, r715 was open. Continuing the analysis, I noticed that c806 was leaking. Swap 715 and c806 c718 ze nascimento
PHILCO PCS-2956
Horizontal change, turns on works normally and suddenly burns out again. Swap c7283n3/1k6 was c 2n2 I replaced it and plz Eronaldo
PHILCO PCM-2051
CP01R0 		It doesn't come out of stand-by by pressing power on the CR or CH+ TV. The LED wouldn't turn on, blinking. Normal power supply voltages high 110v and also low (in stand-by) Replace deflector coil TODDY
PHILCO PCS 2976
High power supply 130 v giving 150 v if turning off R 919 120 k amended jps elet cg
PHILCO/ GRADIENTE TP 2921
Turns off after +or- 10min and stays on std by Ic 501 tea1507p overheating Replace the same livo tecnovideo ps
PHILCO TP 2052N
Power supply pulsing, LED blinking, slow to turn on C 913
PHILCO TP 2052N
Does not tune channels or poor tuning Cristal mf 201 Manoel
PHILCO PC 20R38
Screen with retrace, no brightness or contrast C301 0.47yf/35v close to ci oscillator AdrianChapadão
PHILCO PCM-2051
LED blinking and power supply oscillating Capacitor c913 1uf pardalzito
TV PHILCO 29 TPF-2902 E OUTRAS TVS
No image (brightness), normal sound, with high voltage, trc filament lights up and normal voltages on the rgb. Oxidized tube connector, remove and replace the tube plate and it's shiny! Clean the TRC terminals, spray with WD40, remove the TRC plate several times or if it doesn't look good, replace the connector! Dreamshacker
PHILCO TPF 2130
It turns on but when the relay goes off it turns off and stays on standby flashing Replace o ic 601 (stv 9302a allanaeletronico
PHILCO PC-2035
CPH-03 		Horizontal synchronism C 613 with leak To replace Alvaro
PHILCO TP 2921
GRS 		Power supply +b 130 +b 10 +b36 only the +b 6.5v does not work Micronas vtc 4942 Replace micronas along with the eeprom obs. Heat the 35 watt soldering iron and unplug it to carry out the welding ok luiztvsom
PHILCO TP 2021
GRS 		130v power supply at 0 volts 330 k resistor r 509 open Replace r 509 smd I replaced it and it worked fine luiztvsom
PHILCO TP1454
**** 		The LED turns on and when you turn on the TV it turns off. Does not start Was replaced r-715 =3k3 was cut. Armando