Philco Repair Tips
Search: philco
Results: 4811
Results: 4811
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
TPF 2140
|
It doesn't turn on and it doesn't work on standby. | C 930 with leak in the power supply primary | levilp | |
| PHILCO |
PCM2044
CPH05 |
Vertical fexado. | R.602 | Replace. | |
| PHILCO |
PCS-2956
CP-01-LR01 |
Power supply does not start and chopper driver smokes on pin 7 | C922 short (1.0 nf) I replaced it and the problem was solved. | Note: as the c922 is on the pulse line (130v) the power supply activates and disarms successively. | Tecnogil Eletronica |
| PHILCO |
PT20V56
|
Vertical beam and then switches off | Ceramic capacitor c614 | ELETRONICAAC | |
| PHILCO |
TP20V56
|
Vertical beam and then switches off | Ceramic capacitor c614 | Ac electronics | |
| PHILCO |
PCS2952
|
Dark image with little contrast | C 716 short /r706 open | betoteck | |
| PHILCO |
TPF 2121
|
Morta (nem da stand by) | D908 e c914 | Obs: mude c914 p/ 1000y/35v | VSE Eletrônica(Ádrian) |
| PHILCO |
TP2054
|
Does not turn on, LED is off. | R 911 amended. | Replace. | |
| PHILCO |
PCM2044
|
Lack of sync and drizzle | C205 - agc and c702 sync. I changed the caps. It started working normally again. |
The two electro/capacitors with high esr. | vxm |
| PHILCO |
TP1452N
|
Does not turn on, stays on standby | When the TV is on stand by with the LED on, replace the zd923 4.7 volt diode and the zd922 3.9 volt diode. | Edilson Ribeiro | |
| PHILCO |
TPF 2941
|
Does not turn on or the LED lights up | All voltages are normal, and the TV does not turn on; fed up with stress, I decided to change [x1] that little crystal that is next to every micro, in this case x1 = 20,250, I changed it, I confirmed, it was the one, [if] it happens, sound's the tip | fabinho@3a | |
| PHILCO |
PCR1449
CPH06M |
C912 with leak, change, note tsound is no general voltage in the secondary | ars | ||
| PHILCO |
PCM-2044
|
When the TV was turned on, it worked with a lot of flickering on the screen and it was difficult to maintain the tuning of a channel and when changing channels it got even worse, it shook the whole screen and was like a simonism of vertical and horizontal | The capacitor c710 with cold soldering, I resoldered it and it was file | It is located next to the dryve of the horizontal | |
| TV PHILCO |
TP 29C21
|
TV doesn't work, STD-BY light stays on | Solution replaced the d-916 smd | jaironuness | |
| PHILCO |
PCM 2044
|
When turning on the image comes back to normal after a while the screen becomes clear until the image disappears | Replace ci tda 8361 s7 | ||
| PHILCO |
PCM 2044
|
No image. No sound, no OSD, screen flashing on the power pin, the voltage fluctuates on and off, disconnect pin 35 on the micro controller and the TV stops turning off. So sound the screen is white as if the screen was at maximum but without a delay line | Tube exhausted zerrrrrrrrrrado | ||
| PHILCO |
PCS-2952
|
Arming protection | C727/470p+r718-10k+dz712/8,2 | JACKSSOM | |
| PHILCO |
TP-2052
|
Does not turn on, turns on standby | Res. 942 12k | vicena | |
| PHILCO |
TP2054
*** |
The TV turned on when I wanted, it worked for about 5 minutes and turned off, I noticed that the LED was lit dimly, you started it, it just blinked, I checked +b it was oscillating when I measured the voltage on the fet, normal voltage, I changed the IC 901, nothing changed, I released pin 3 of the IC 902 photo coupler the voltage at +b was normal and the TV worked normally, but it presented another defect with a black stripe on top. I replaced the c-715 6n8/1kv with 8n7/1kv and the strip normalized the image was good, but the sides dir / left making curves and ghost image I checked c-911 and everything was resolved. | Replace c-715 c-911 | C-715 de 6n8/1kv por 8n7/1kv c-911 470x25v. | wagner |
| PHILCO |
PC2039.
|
No audio/normal image. | Capacitor c-513=10nf was detected, defective. | The same was replaced and only joy. | Armando da Eletrônica só Tv. |