Philco Repair Tips
Search: philco
Results: 4811
Results: 4811
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
PT 1554
CP02 RO |
TV defect has no image in 15 seconds | TV turns off without showing image just plot | Ci power supply ic 901 tda16846 p d 909 short burn r 910 and 912 | Everardes |
| PHILCO |
PCM2051
|
Sometimes it turns on and doesn't turn on and when it turns on over time it turns off by itself. | C708 ou c709 | Sandro T Grachet | |
| PHILCO |
TP 2054
|
Dark screen with sound and menu ok, | Cause diode leakage d 602 | ELETRONICA ROBSON(DEBIQUE) | |
| PHILCO |
PCS 2956
|
Vertical closed | Vertical was burned out, I replaced the vertical, it remained closed | R 709 open 1r | negodrama |
| PHILCO |
TP-1452N
|
Volume increases only in 3 stages | Program memory or press the channel +/- key and plug in for 15 seconds and adjust | ELETRONICA ARNI L. LEAL-SC | |
| PHILCO GRADIENTE |
TODOS DE 29''
TODOS COM MICRONAS |
Transistor h burns out for no apparent reason | Check, change all filter+b capacitors of driver h | Place bu that supports higher current and higher peak voltage | josé carlos |
| PHILCO |
TP14U56
|
Normal image then goes dark and tsound is only sound | Diode d 602 altered | ||
| PHILCO |
PC1444
CPH05 |
Ugly image (no contrast) no sound. | Tda8361 with internal defect | Replace the tda8361 e5 | josé carlos |
| PHILCO |
PC1444
CPH05 |
Image shaking, synchronization and missing color | Change cap 205. exhausted 2.2mf 50v | josé carlos | |
| PHILCO |
TP-2052N
|
TV asking for password, in my case it asked for password on channel 3. | Reset to memory. | Press the channel + and channel - keys and plug in for 15 seconds. | |
| PHILCO |
TP-1454
|
Doesn't start | D-909 opened d-908 changed | GBS.Eletrônica | |
| PHILCO |
TP-1454
|
Doesn't start | D-909 amended | GBS.Eletrônica | |
| PHILCO |
PCM1444
|
Does not respond to keyboard commands | Cause:r713 (changed or opened) | Replace and resolve | jarbas santos |
| PHILCO |
TP2920
|
Turns on, no image appears, and then turns off, goes into protection | Check +b 50v from the vertical ci should have around 42v on pin 3 vertical ci, if it is below this ci value defective. | Bruske | |
| PHILCO |
PH21B
|
Turn on the TV perfect image after a few minutes the image starts to lose its brightness due to this defect | In the abl but it is not, defect in the kinescope board transistor bf 423 with emitter collector leak | Replace transistor v 903 bf 423 | fernando timbauba PE |
| PHILCO |
PCM2044
|
It doesn't have 95 volts | C911 220mfx160vols reset | juci | |
| PHILCO |
TP-2921
|
Excess green color | Eprom reprogramming. and a correction: to enter the service mode of this TV, press menu on the control and on the panel at the same time and wait a few seconds. | FERNANDO | |
| PHILCO |
PCS2952
|
Vertical closed | Ic601-la7833/c610-100/63v/d703 e r720-1r | Replace mentioned items | eletronicaapolo |
| PHILCO |
TPF 2130 REAL FLAT
|
My TV had the LED on when I pressed the power button and it went into standby mode | I replaced IC 601 (STV 9302 a) and resoldered the 936 resistor which was with capacitor glue | TV operating normally, I want to thank everyone for the tip and good luck | Jorge Luiz |
| PHILCO |
TRANSGLOBE B 481
|
Low volume and noisy on all tracks | Transistor t 406 pb 6015 after changing all the electrolytics in the amplifier, and losing some cable wires, I took it out and tested it and it said it was good, I decided to change it, damn the old radio came back to life | Marcio |