Philco Repair Tips
Search: philco
Results: 4811
Results: 4811
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
PCM 1446
|
No sound with amplification on tda 8361 | Tda 8361 | I replaced it and just joy! | sinezio lbano |
| PHILCO |
TP2054
|
The stand by LED turns on, when trying to turn on the power supplys they are ok, but it does not oscillate and the LED keeps blinking | Fly back, when deactivating the micro protection, it oscillated and burned the abl line | Replace fly back, ov2094-d1 | bick |
| PHILCO |
PC 1445
|
No color | Resistor r118 (18k) aberto | Replace resistor r118 (18k) | rogerio santos |
| PHILCO |
TPC2910
|
The unfortunate one doesn't open the sides of the screen (belly on the sides) | Change q405, adjust ew | marcos hifi | |
| PHILCO |
TPF2121C
|
TV with dark image, normal sound. | Check transistor bc 857- q 703. | sergiozap | |
| PHILCO |
PCM-1444
|
Flashing standby LED | Cold soldering on c706 | Resolder the c706 and check if tsound are more points to be resoldered on the same line. | Carlos Carbonari |
| PHILCO |
PCS2976
|
R919 20k amended | amsmariano | ||
| PHILCO |
PCS 2952
|
TV with the frame a little closed as soon as it turns on, as soon as it tunes a channel it folds horizontally and the tune goes out. | W. 720 47/25 from power supply +9 | Benê-Nepomuceno MG | |
| PHILCO |
TP 2010
PCI016A |
LED wouldn't turn on, blinking with a small power supply crackle | Resoldar c-921 smd e x 301 | eletroléo | |
| PHILCO |
TP 20V56
|
Sem audio no av | Replace i.c 490 | Replace i.c 490 | |
| PHILCO |
PCM1446
|
No color | C153 no pino 33 do micro | Carlos Afro | |
| PHILCO |
PCS 2956
|
Excessive high voltage, popping in the pacifier | Wide capacitor,c 706 and c 709. | jrmonitores | |
| PHILCO |
PCS 2956
|
Rainbow effect | Vertical output, tda 8351 fits tda 8356 in place | jrmonitores | |
| PHILCO |
PCS 2956
|
Didn't care | Capacitor c921 shorted, do not remove, replace with another of the same value | jrmonitores | |
| PHILCO |
PC2039 E OUTRAS
|
Retrace lines, dull | C 801 on the trc board | To replace | Ricardo segab |
| TV PHILCO |
TP-2052N
|
It doesn't turn on after heating, if the manual switch off doesn't turn on, just by the control, it turns off and on normally. | Change c708 c709 and zd702, and from the power supply only leave the smd ones if that doesn't work, also change the smd ones | Reginaldo_nobre | |
| PHILCO |
TP-1452N
|
It doesn't turn on when it turns on, it turns off the LED on the STBAY 8817, Joelton's friend | It was transistor q702 that connected the open horizontal driver coil | Replace the transistor blz it works again | marcos melo cascavel ce |
| PHILCO |
TP-1452N
|
Screen blown (retraces), +b 180v low. | C-719 shorted, replace it. | Ronan | |
| PHILCO |
21PT9467C/78
|
Vertical closed | Ic351/ tda4865aj, r309 /01r, r310/o1r, d303/byw36, d304/byw36, d305/ba158, j308/067r | ELETRONICA ARNI-LEOBERTO LEAL /SC | |
| PHILCO |
21PT9467C/78
|
Vertical closed | Tda4865aj, r309, r310, d303, d304, d305, j308 | Help yourself leave your tip | ELETRONICA ARNI-LEOBERTO LEAL /SC |